參數資料
型號： TE28F640P30T85
廠商： INTEL CORP
元件分類： DRAM
英文描述： Intel StrataFlash Embedded Memory
中文描述： 4M X 16 FLASH 1.8V PROM, 85 ns, PDSO56
封裝： 14 X 20 MM, TSOP-56
文件頁數： 65/102頁
文件大?。?/td> 1609K
代理商： TE28F640P30T85
1-Gbit P30 Family
Datasheet
Intel StrataFlash
Embedded Memory (P30)
Order Number: 306666, Revision: 001
April 2005
65
Two basic sequences repeat in this phase: loading of the write buffer, followed by buffer data
programming to the array. For BEFP, the count value for buffer loading is always the maximum
buffer size of 32 words. During the buffer-loading sequence, data is stored to sequential buffer
locations starting at address 0x00. Programming of the buffer contents to the flash memory array
starts as soon as the buffer is full. If the number of words is less than 32, the remaining buffer
locations must be filled with 0xFFFF.
Caution:
The buffer must be completely filled for programming to occur. Supplying an address outside of the
current block's range during a buffer-fill sequence causes the algorithm to exit immediately. Any
data previously loaded into the buffer during the fill cycle is not programmed into the array.
The starting address for data entry must be buffer size aligned, if not the BEFP algorithm will be
aborted and the program fails and (SR[4]) flag will be set.
Data words from the write buffer are directed to sequential memory locations in the flash memory
array; programming continues from where the previous buffer sequence ended. The host
programming system must poll SR[0] to determine when the buffer program sequence completes.
SR[0] cleared indicates that all buffer data has been transferred to the flash array; SR[0] set
indicates that the buffer is not available yet for the next fill cycle. The host system may check full
status for errors at any time, but it is only necessary on a block basis after BEFP exit. After the
buffer fill cycle, no write cycles should be issued to the device until SR[0] = 0 and the device is
ready for the next buffer fill.
Note:
Any spurious writes are ignored after a buffer fill operation and when internal program is
proceeding.
The host programming system continues the BEFP algorithm by providing the next group of data
words to be written to the buffer. Alternatively, it can terminate this phase by changing the block
address to one outside of the current block’s range.
The Program/Verify phase concludes when the programmer writes to a different block address;
data supplied must be 0xFFFF. Upon Program/Verify phase completion, the device enters the
BEFP Exit phase.
11.3.4
BEFP Exit Phase
When SR[7] is set, the device has returned to normal operating conditions. A full status check
should be performed at this time to ensure the entire block programmed successfully. When exiting
the BEFP algorithm with a block address change, the read mode will not change. After BEFP exit,
any valid command can be issued to the device.
11.4
Program Suspend
Issuing the Program Suspend command while programming suspends the programming operation.
This allows data to be accessed from the device other than the one being programmed. The
Program Suspend command can be issued to any device address. A program operation can be
suspended to perform reads only. Additionally, a program operation that is running during an erase
suspend can be suspended to perform a read operation (see
Figure 41, “Program Suspend/Resume
Flowchart” on page 86
).
相關PDF資料
PDF描述
TE28F128P30B85 Intel StrataFlash Embedded Memory
TE28F160B3-B120 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE
TE28F800B3-B120 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE
TE28F400B3-B120 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE
TE28F160B3-B150 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE
相關代理商/技術參數
參數描述
TE28F640P30T85A 功能描述:IC FLASH 64MBIT 85NS 56TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:3,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K (4K x 8) 速度:100kHz，400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) 其它名稱:CAV24C32WE-GT3OSTR
TE28F640P33B85A 功能描述:IC FLASH 64MBIT 85NS 56TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:2,000 系列:MoBL® 格式 - 存儲器:RAM 存儲器類型:SRAM - 異步 存儲容量:16M（2M x 8，1M x 16） 速度:45ns 接口:并聯 電源電壓:2.2 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFBGA 供應商設備封裝:48-VFBGA（6x8） 包裝:帶卷 (TR)
TE28F640P33T85A 功能描述:IC FLASH 64MBIT 85NS 56TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR)
TE28F800B3 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:SMART 3 ADVANCED BOOT BLOCK 4-, 8-, 16-, 32-MBIT FLASH MEMORY FAMILY
TE28F800B3B110 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*