參數資料
型號： TDA8030HL
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： USB smart card reader (OTP or ROM)
中文描述： SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件頁數： 42/57頁
文件大小： 228K
代理商： TDA8030HL
2003 Jul 04
42
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 42
Power-on value for Select end-point
Table 43
Description of the Power-on value for Select end-point bits
Table 44
Power-on value for Set end-point status; notes 1 and 2
Notes
1.
2.
X = dont care.
def means that the bit can be set if the end-point is of the specified type.
FUNCTION
7
6
5
4
0
3
0
2
0
1
0
0
Full or empty
Stall
Set-up
Packet overwritten
Sent NAK
Reserved
0
FUNCTION
DESCRIPTION
Full or empty
If set to logic 1, the buffer of the selected end-point is full.
In the event of an output end-point, this bit is cleared by executing the Clear Buffer command, if
the buffer was not overwritten.
In the event of an input end-point, this bit is set by the Validate Buffer command.
If set to logic 1, the selected end-point is stalled.
If set to logic 1, the last received packet for the selected end-point was a set-up packet. The
value of this bit is updated after each successfully received packet (i.e. an ACKED package on
that particular end-point).
If set to logic 1, the previously received packet was overwritten by a set-up packet. The value of
this bit is cleared by the Select End-point command.
If set to logic 1, the device has sent a NAK. If the host sends an output packet to a filled output
buffer, the device returns a NAK. If the host sends an input token to an empty input buffer, the
device returns a NAK.
This bit is set when a NAK is sent and the Interrupt On Nak feature is enabled.
This bit is reset after the device has sent an ACK after an output packet or when the device has
seen an ACK after sending an input packet. It is only defined for the 2 physical control
end-points.
Stall
Set-up
Packet overwritten
Sent NAK
FUNCTION
7
6
0
5
0
4
3
2
1
0
CTRL EP
GEN IN/OUT
GEN IN
Stall
Disable
Rate feedback
mode
Interrupt unmasked
Conditional stall
0
def
X
X
def
def
def
def
def
def
0
0
X
X
X
X
X
def
相關PDF資料
PDF描述
TDA8031 USB smart card reader (OTP or ROM)
TDA8031HL USB smart card reader (OTP or ROM)
TDA8302 SMALL SIGNAL COMBINATION IC FOR COLOUR TV
TDA8931 Power comparator 1 X 20 W
TDA8931T Power comparator 1 X 20 W
相關代理商/技術參數
參數描述
TDA8031 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM)
TDA8031HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM)
TDA8034AT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface
TDA8034AT/C1 制造商:NXP Semiconductors 功能描述:Cut Tape
TDA8034AT/C1,112 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*