- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8030HL (NXP SEMICONDUCTORS) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8030HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 18/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8030HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
18
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.1.4
ISO UART REGISTERS
8.1.4.1
UART transmit register
When the microcontroller wants to transmit a character to
the card, it writes the data in direct convention in this
register.
The transmission:
Starts at the end of this writing (2 clock cycles after the
rising edge of WR) if the previous character has been
transmitted and if the extra guard time has expired
Starts at the end of the extra guard time if this one has
not expired
Starts at 13.5 ETU in manual mode and 15 ETU in
automatic mode if the previous character has been
NAKed by the card; see Section 8.1.4.4
Does not start if the transmission of the previous
character is not completed.
When the transmission is completed:
In T = 0, bit TBE is set at 11.5 ETU, and bit PE in the
event of parity error
In T = 1, bit TBE is set at 10.5 ETU.
In the event of synchronous cards (bit SAN set within
UCR2), UT0 is only relevant and is copied on the I/O of the
card. It is possible to write within the UTR before setting
the transmission mode, which may be useful in some
cases.
Table 9
UART transmit register (address 0DH; write only); note 1
Note
1.
All bits are cleared after reset.
7
6
5
4
3
2
1
0
UT7
UT6
UT5
UT4
UT3
UT2
UT1
UT0
8.1.4.2
UART receive register
Whenthemicrocontrollerwantstoreaddatafromthecard,
it reads it from this register in direct convention.
In the event of synchronous cards, only UR0 is relevant
and is a copy of the state of the card I/O.
In the event of parity error:
The bit PE in the status register USR is set at 10.5 ETU
and INT0 falls LOW
In protocol T = 0, the received byte is not stored in URR;
In protocol T = 1, the received byte is stored.
In both protocols, when a character has been stored, then
the bit RBF in the status register USR is set at 10.5 ETU.
This bit is reset when the character has been read from the
URR.
When the URR is empty, then bit FE (in the MSR) is set as
long as no character has been received.
Table 10
UART receive register (address 0DH; read only); note 1
Note
1.
All bits are cleared after reset.
7
6
5
4
3
2
1
0
UR7
UR6
UR5
UR4
UR3
UR2
UR1
UR0
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8031 | USB smart card reader (OTP or ROM) |
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8031 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。