- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8030HL (NXP SEMICONDUCTORS) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8030HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 29/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8030HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
29
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.2
SUPPLY
The supply to the chip is delivered by the USB-bus (pins
V
and UGND).
8.2.1
P
OWER SWITCH CONTROL
A power switch control is used in order to limit the inrush
current when plugging the reader into the bus. The main
decoupling capacitor is connected to the output of this
power switch control (pin V
DD
).
8.2.2
3.3 V
REGULATOR
The output voltage of the 3.3 V linear regulator is used for:
Powering-up the microcontroller and the ISO7816
UART
It is the reference voltage for the signalling pull-up
resistor connected to pin D+.
If this voltage is used within the application, the current
should not exceed 10 mA.
For stability reasons, a 1
μ
F low ESR decoupling capacitor
is needed between the output of the regulator (V
DDD
) and
the specific regulator ground (DGND).
For programming the EPROM of the TDA8030; TDA8031,
by applying a logic 1 to pin CPROG it will disable the
regulator, so that the microcontroller will be powered-up at
5 V.
8.2.3
DC-
TO
-DC
CONVERTER
In case of a 5 V card, the card buffers are supplied by an
inductive DC-to-DC converter.
In case of a 3 or 1.8 V card, the DC-to-DC converter is
transparent and the card buffers are then supplied directly
by V
DD
.
The external components for the DC-to-DC converter
should be an inductance of 6.8
μ
H, a low ESR capacitor of
1
μ
F and a Schottky diode (type BAT54).
The power efficiency is approximately 85% up to
I
CC
= 55 mA. The current is limited at 100 mA during the
start-up phase to avoid spurious supply drop-outs.
The DC-to-DC converter is transparent for a 3 V card.
handbook, full pagewidth
MGU887
low
up
P drive
N drive
reset
clock
VDD
Vref
VUP
LX
Fig.7 DC-to-DC converter.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8031 | USB smart card reader (OTP or ROM) |
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8031 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。