參數資料
型號： STV2001
廠商： 意法半導體
英文描述： I2C SINGLE FREQUENCY DEFLECTION PROCESSOR AND 120 MHz RGB PREAMPLIFIER
中文描述： 撓度的I2C單頻處理器和120兆赫的RGB前置放大器
文件頁數： 33/46頁
文件大小： 528K
代理商： STV2001
STV2001
33/
46
14.4.2 - Contrast Adjustment (7 bits)
The contrast adjustment is made by simultaneous-
ly controlling the gain of three internal variable
gain amplifiers through the I
2
C bus interface. The
contrast adjustment allows covering a range high-
er than 40 dB. This adjustment is refreshed during
the vertical retrace time.
14.4.3 - ABL Control
The STV2001 has an ABL input (automatic beam
limitation) to attenuate RGB video signals accord-
ing to beam intensity.
The operating range is typically 2.5 V, from 5.3 V
to 2.8 V. A typical 12 dB Max. attenuation is ap-
plied to the signal whatever the current gain. Refer
to Figure 16 for ABL input attenuation range.
In the case of software control, the ABL input must
be pulled to AV
CC
through a resistor to limit power
consumption.
ABL input voltage must not exceed VAV
CC
. Input
resistor is 10k
.
Figure 17.
14.4.4 - Brightness Adjustment (6 bits)
As with contrast adjustment, brightness is control-
led by I
2
C.
The brightness function consists of adding the
same DC offset to the three R, G, B signals after
contrast amplification. This DC-Offset is present
only outside the blanking pulse (see
Figure 19
).
The DC output level is forced to "INFRA-BLACK"
level (V
DC
) during the blanking pulse.
14.4.5 - Drive Adjustment (3 x 8 bits)
To adjust the white balance, the device offers the
possibility of separately adjusting the overall gain
of each complete video channel. Each channel
gain is controlled by I
2
C (8 bits each). The very
large drive adjustment range (48dB) allows differ-
ent standard or custom color temperatures.
The drive adjustment is also used to adjust the
output voltages at the optimum amplitude to drive
the C.R.T drivers, keeping the whole contrast con-
trol for end-users only. The drive adjustment is
made after the contrast and brightness so that the
white balance remains correct when BRT is ad-
justed.
14.4.6 - Output Stage
The three output stages (see
Figure 18
) incorpo-
rate three functions:
The blanking stage: when the internal
generated blanking pulse is high, the three
outputs are switched to a voltage which is
400 mV lower than the BLACK level. The
black level is the output voltage with minimum
brightness when the input signal video
amplitude is equal to "0".
The output stage itself: a large bandwidth
output amplifier which can deliver up to 5V
PP
on the three outputs (for 0.7 V video signal on
the inputs).
The output CLAMP: the IC also incorporates
three internal output clamps (sample and hold
system) to fix the "INFRA-BLACK" level
(VDC) at 1.1V during blanking.
The overall waveforms of the output signal accord-
ing to the different adjustments are shown in
Figure 19.
and
Figure 20.
2
0
-2
-4
-6
-8
-10
-12
-141
2
3
4
5
6
7
8
9
Attenuation (dB)
V
IN
(V)
相關PDF資料
PDF描述
STV2100 TV/Video Signal Processor
STV2112 Color Decoder Circuit
STV2116 Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode
STV2118A Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode
STV2151B Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode
相關代理商/技術參數
參數描述
STV200K-10Y 制造商:Sola/Hevi-Duty 功能描述:
STV200K-27Y 制造商:Sola/Hevi-Duty 功能描述:
STV200N55F3 功能描述:MOSFET N-channel 55 V RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube
STV-201-1 制造商:TE Connectivity 功能描述:
STV202 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TV Power Schematic
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*