參數資料
型號： STLC2500
廠商： 意法半導體
英文描述： BLUETOOTH⑩ SINGLE CHIP
中文描述： 單芯片藍牙⑩
文件頁數： 20/23頁
文件大小： 241K
代理商： STLC2500
STLC2500
20/23
Table 23. GPIO multiplexing
8.5 The I2C interface
The I2C interface (version 2.1) has been specified by Philips.
The I2C interface is used to access I2C peripherals.
The implemented interface is a fast master I2C; it has full control of the interface at all times. I2C slave
functionality is not supported, forcing attached devices to be slave, otherwise bus contention will occur.
9
The UART transport Layer has been specified by the Bluetooth SIG and allows HCI level communication
between a Bluetooth controller (STLC2500) and a Host (e.g. a GSM), via a serial line.
The objective of this HCI UART Transport Layer is to make possible to use Bluetooth HCI over a serial
interface between two UARTs on the same PCB. The HCI UART Transport Layer assumes that the UART
communication is free from line errors.
HCI UART TRANSPORT LAYER
UART Settings
The HCI UART Transport Layer uses the following settings for RS232:
– Baud rate: configurable (default baud rate 115.2 [kbps])
– Number of data bits: 8
– Parity bit: no parity
– Stop bit: 1 stop bit
– Flow control: RTS/CTS
– Flow-off response time: 3 ms
Flow control with RTS/CTS is used to prevent temporary UART buffer overrun. It should not be used for
flow control of HCI, since HCI has its own flow control mechanism for HCI commands, HCI events and
HCI data.
If CTS is high, then the Host/Bluetooth controller is allowed to send.
If CTS is low, then the Host/Bluetooth controller is not allowed to send.
The flow-off response time defines the maximum time from setting RTS low until the byte flow actually
stops. The RS232 signals should be connected in a null-modem fashion, i.e. the local TXD should be con-
nected to the remote RXD and the local RTS should be connected to the remote CTS and vice versa.
Figure 9. UART Transport Layer
Multiplexed GPIOs
WLAN
(See also table 19.)
WLAN 1
WLAN 2
WLAN 3
WLAN 4
I2C
PCM
GPIO
I2C clock
I2C data
[PCM or GPIO]
[PCM or GPIO]
[I2C or GPIO]
[I2C or GPIO]
PCM sync 1
PCM sync 2
GPIO 0
GPIO 1
GPIO 2
GPIO 3
BLUETOOTH
HOST
BLUETOOTH
HOST
CONTROLLER
BLUETOOTH HCI
HCI UART TRANSPORT LAYER
相關PDF資料
PDF描述
STLC3055 WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3055Q WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3055QTR WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3065 WLL SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3065QTR WLL SUBSCRIBER LINE INTERFACE CIRCUIT
相關代理商/技術參數
參數描述
STLC2500A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Bluetooth Single Chip
STLC2500ATR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Bluetooth Single Chip
STLC2500C 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:BluetoothTM EDR Single Chip
STLC2500DB-EDB2G 制造商:ST Ericsson 功能描述:PCB DAUGHTERBOARD WITH STLC2500DB DEVICE ASSEMBLED?????? - Bulk 制造商:ST-Ericsson 功能描述:PCB DAUGHTERBOARD WITH STLC2500DB DEVICE ASSEMBLED?????? - Bulk 制造商:ST-Ericsson 功能描述:STLC2500DB-EDB2G Full Bluetooth 3.0 + HS Lisbon
STLC2541 制造商:STMicroelectronics 功能描述:EVALBOARD - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*