REV. 4.2.2 2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO ISR[3:1]: Interrupt Status These bits indicate the source for a pending inter" />
參數資料
型號： ST16C2552CJ44-F
廠商： Exar Corporation
文件頁數： 11/34頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 16 字節
規程： RS232，RS485
電源電壓： 3.3 V ~ 5 V
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1257-5
ST16C2552
19
REV. 4.2.2
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source Table 8).
ISR[5:4]: Reserved
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.6
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Reserved
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 9 shows the complete selections.
TABLE 9: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
BIT-7
BIT-6
RECEIVE
TRIGGER
LEVEL
COMPATIBILITY
0
1
0
1
0
1
1 (default)
4
8
14
Table-A. 16C550,
16C2550, 16C2552,
16C554, 16C580 com-
patible.
FCR
相關PDF資料
PDF描述
XR88C681CJ-F IC UART CMOS DUAL 44PLCC
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
相關代理商/技術參數
參數描述
ST16C2552CJ44TR 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C2552CJ44TR-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2552CQ48 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
ST16C2552IJ 制造商:Exar Corporation 功能描述:2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44
ST16C2552IJ44 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: 制造商:Exar Corporation 功能描述:UART, 44 Pin, Plastic, PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*