- 您現在的位置：買賣IC網 > PDF目錄365651 > SN74BCT8374ANTE4 (Texas Instruments, Inc.) SCAN TEST DEVICES WITH OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS PDF資料下載
參數資料
| 型號： | SN74BCT8374ANTE4 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | SCAN TEST DEVICES WITH OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS |
| 中文描述： | 掃描測試設備與八路D型邊沿觸發觸發器 |
| 文件頁數： | 5/26頁 |
| 文件大?。?/td> | 474K |
| 代理商： | SN74BCT8374ANTE4 |
SN54BCT8374A, SN74BCT8374A
SCAN TEST DEVICES
WITH OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS
SCBS045E – JUNE 1990 – REVISED JULY 1996
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
test architecture
Serial-test information is conveyed by means of a 4-wire test bus, or TAP, that conforms to IEEE Standard
1149.1-1990. Test instructions, test data, and test control signals all are passed along this serial-test bus. The
TAP controller monitors two signals from the test bus, TCK and TMS. The TAP controller extracts the
synchronization (TCK) and state control (TMS) signals from the test bus and generates the appropriate on-chip
control signals for the test structures in the device. Figure 1 shows the TAP-controller state diagram.
The TAP controller is fully synchronous to the TCK signal. Input data is captured on the rising edge of TCK, and
output data changes on the falling edge of TCK. This scheme ensures that data to be captured is valid for fully
one-half of the TCK cycle.
The functional block diagram shows the IEEE Standard 1149.1-1990 4-wire test bus and boundary-scan
architecture and the relationship among the test bus, the TAP controller, and the test registers. As shown, the
device contains an 8-bit instruction register and three test-data registers: an 18-bit boundary-scan register, a
2-bit boundary-control register, and a 1-bit bypass register.
Test-Logic-Reset
Run-Test/Idle
Select-DR-Scan
Capture-DR
Shift-DR
Exit1-DR
Pause-DR
Update-DR
TMS = L
TMS = L
TMS = H
TMS = L
TMS = H
TMS = H
TMS = L
TMS = H
TMS = L
TMS = L
TMS = H
TMS = L
Exit2-DR
Select-IR-Scan
Capture-IR
Shift-IR
Exit1-IR
Pause-IR
Update-IR
TMS = L
TMS = L
TMS = H
TMS = L
TMS = H
TMS = H
TMS = L
TMS = H
TMS = L
Exit2-IR
TMS = L
TMS = H
TMS = H
TMS = H
TMS = L
TMS = H
TMS = L
TMS = H
TMS = H
TMS = H
TMS = L
Figure 1. TAP-Controller State Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| SN54BCT8374AFK | SCAN TEST DEVICES WITH OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS |
| SN54BCT8374AJT | SCAN TEST DEVICES WITH OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS |
| SN74BCT8374ANT | SCAN TEST DEVICES WITH OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS |
| SN74BCT8374ADWR | Replaced by BQ20Z80A-V110 : Impedance Track (TM) 1% accurate Gas Gauge for LiIon batteries SBS1.1 compliant 38-TSSOP -40 to 85 |
| SN74BCT8374ADWRE4 | Replaced by BQ20Z80A-V110 : Impedance Track (TM) 1% accurate Gas Gauge for LiIon batteries SBS1.1 compliant 38-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SN74BCT8374NT | 制造商:Texas Instruments 功能描述:Flip Flop, Octal, D Type, 24 Pin, Plastic, DIP |
| SN74BCT899DW | 制造商:Texas Instruments 功能描述: |
| SN74CB373384DBQR | 制造商:Texas Instruments 功能描述: |
| SN74CB3Q16210DGGR | 功能描述:數字總線開關 IC Fixed LDO Volt Reg RoHS:否 制造商:Texas Instruments 開關數量:24 傳播延遲時間:0.25 ns 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TSSOP-56 封裝:Reel |
| SN74CB3Q16210DGGRE4 | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。