參數資料
型號: SM320F28335GHHAEP
廠商: Texas Instruments
文件頁數: 101/167頁
文件大?。?/td> 0K
描述: IC DIGITAL SIGNAL CTLR 179-BGA
產品培訓模塊: ControlSUITE
Motor Signal Chain Overview
TPS75005 Single IC Power for C2000 MCU
標準包裝: 189
系列: TMS320F28x3x Delfino™, C2000™
核心處理器: C28x
芯體尺寸: 32-位
速度: 150MHz
連通性: CAN,EBI/EMI,I²C,McBSP,SCI,SPI,UART/USART
外圍設備: DMA,POR,PWM,WDT
輸入/輸出數: 88
程序存儲器容量: 512KB(256K x 16)
程序存儲器類型: 閃存
RAM 容量: 34K x 16
電壓 - 電源 (Vcc/Vdd): 1.805 V ~ 1.995 V
數據轉換器: A/D 16x12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 179-LFBGA
包裝: 托盤
產品目錄頁面: 718 (CN2011-ZH PDF)
其它名稱: 296-25243
SPRS581D – JUNE 2009 – REVISED MAY 2012
When initially debugging a device with the password locations in flash programmed (i.e., secured), the
emulator takes some time to take control of the CPU. During this time, the CPU will start running and may
execute an instruction that performs an access to a protected ECSL area. If this happens, the ECSL will
trip and cause the emulator connection to be cut. Two solutions to this problem exist:
1. The first is to use the Wait-In-Reset emulation mode, which will hold the device in reset until the
emulator takes control. The emulator must support this mode for this option.
2. The second option is to use the “Branch to check boot mode” boot option. This will sit in a loop and
continuously poll the boot mode select pins. The user can select this boot mode and then exit this
mode once the emulator is connected by re-mapping the PC to another address or by changing the
boot mode selection pin to the desired boot mode.
NOTE
When the code-security passwords are programmed, all addresses between 0x33FF80
and 0x33FFF5 cannot be used as program code or data. These locations must be
programmed to 0x0000.
If the code security feature is not used, addresses 0x33FF80 through 0x33FFEF may be
used for code or data. Addresses 0x33FFF0 – 0x33FFF5 are reserved for data and
should not contain program code. .
The 128-bit password (at 0x33 FFF8 – 0x33 FFFF) must not be programmed to zeros. Doing
so would permanently lock the device.
disclaimer
Code Security Module Disclaimer
THE CODE SECURITY MODULE (CSM) INCLUDED ON THIS DEVICE WAS DESIGNED
TO PASSWORD PROTECT THE DATA STORED IN THE ASSOCIATED MEMORY
(EITHER ROM OR FLASH) AND IS WARRANTED BY TEXAS INSTRUMENTS (TI), IN
ACCORDANCE WITH ITS STANDARD TERMS AND CONDITIONS, TO CONFORM TO
TI'S PUBLISHED SPECIFICATIONS FOR THE WARRANTY PERIOD APPLICABLE FOR
THIS DEVICE.
TI DOES NOT, HOWEVER, WARRANT OR REPRESENT THAT THE CSM CANNOT BE
COMPROMISED OR BREACHED OR THAT THE DATA STORED IN THE ASSOCIATED
MEMORY CANNOT BE ACCESSED THROUGH OTHER MEANS. MOREOVER, EXCEPT
AS SET FORTH ABOVE, TI MAKES NO WARRANTIES OR REPRESENTATIONS
CONCERNING THE CSM OR OPERATION OF THIS DEVICE, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL TI BE LIABLE FOR ANY CONSEQUENTIAL, SPECIAL, INDIRECT,
INCIDENTAL, OR PUNITIVE DAMAGES, HOWEVER CAUSED, ARISING IN ANY WAY
OUT OF YOUR USE OF THE CSM OR THIS DEVICE, WHETHER OR NOT TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE,
BUT ARE NOT LIMITED TO LOSS OF DATA, LOSS OF GOODWILL, LOSS OF USE OR
INTERRUPTION OF BUSINESS OR OTHER ECONOMIC LOSS.
3.2.11 Peripheral Interrupt Expansion (PIE) Block
The PIE block serves to multiplex numerous interrupt sources into a smaller set of interrupt inputs. The
PIE block can support up to 96 peripheral interrupts. On the F28335, 58 of the possible 96 interrupts are
used by peripherals. The 96 interrupts are grouped into blocks of 8 and each group is fed into 1 of 12
CPU interrupt lines (INT1 to INT12). Each of the 96 interrupts is supported by its own vector stored in a
dedicated RAM block that can be overwritten by the user. The vector is automatically fetched by the CPU
on servicing the interrupt. It takes 8 CPU clock cycles to fetch the vector and save critical CPU registers.
Hence the CPU can quickly respond to interrupt events. Prioritization of interrupts is controlled in
hardware and software. Each individual interrupt can be enabled/disabled within the PIE block.
Copyright 2009–2012, Texas Instruments Incorporated
Functional Overview
39
Product Folder Link(s): SM320F28335-EP
相關PDF資料
PDF描述
SMA4306-TL-H IC OSC FOR LASER DIODE SCH6
SN65LVDS047DG4 IC LVDS QUAD DIFF DVR 16-SOIC
SN65LVDS390DG4 IC DIFF LINE RECEIVER HS 16-SOIC
SN65LVDS94DGGG4 IC LVDS SERDES RECEIVER 56-TSSOP
SN74LV4066APW IC SWITCH QUAD 1X1 14TSSOP
相關代理商/技術參數
參數描述
SM320F28335GJZMEP 功能描述:數字信號處理器和控制器 - DSP, DSC EP Digital Signal Controller RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
SM320F28335-HT 制造商:TI 制造商全稱:Texas Instruments 功能描述:Digital Signal Controller (DSC)
SM320F28335KGDS1 功能描述:數字信號處理器和控制器 - DSP, DSC High Temp DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
SM320F28335PTPMEP 功能描述:數字信號處理器和控制器 - DSP, DSC EP Dig Signal Controller RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
SM320F28335PTPS 制造商:Texas Instruments 功能描述:Hirel version of INDUS - 150C Device 制造商:Texas Instruments 功能描述:IC DIGITAL SIGNAL CTRLR 176BGA