參數資料
型號： SiI1161CT100
廠商： Silicon Image, Inc.
英文描述： PanelLink Receiver
中文描述： PanelLink接收機
文件頁數： 43/46頁
文件大小： 398K
代理商： SII1161CT100
SiI
1161
PanelLink Receiver
Data Sheet
39
SiI
-DS-0096-D
Packaging
Thermal Design Options
The
SiI
1161
is packaged in a thermally enhanced 100 pin TQFP with an exposed metal pad (6.5mmx 6.5mm) on
the package for improved thermal dissipation. With the worst-case power consumption and heat dissipation of
the
SiI
1161, its exposed thermal pad requires soldering to the PCB. When operating below the maximum speed
of the
SiI
1161, or in an environment with a maximum ambient lower than 70oC, it may not be necessary to solder
the ePad to the PCB. The board designer should calculate the application-specific thermal resistance and
maximum resulting junction temperature.
Important:
Do
not
place any vias or exposed signal traces beneath the exposed thermal metal pad of the
SiI
1161 on the PCB.
Additional specific guidelines for design of the thermal pad, the solder mask, etc. are on page 39.
ePad Enhancement
The
SiI
1161
is packaged in a 100-pin TQFP package with ePad. The ePad dimensions are shown in Figure 30.
T1
T2
C
C
T3
T4
ePad Dimensions
ePad Height
ePad Width
ePad extension Width
ePad extension Length
Tolerance
typ
0.3
0.7
max
6.5
6.5
0.4
1.0
±0.1
T1
T2
T3
T4
T
All dimensions are in millimeters.
ePad is centered on the package center lines.
Silicon Image recommends that the ePad be
electrically grounded on the PCB.
The ePad
must not be electrically connected to any
other voltage level except ground (GND).
A clearance of at least 0.25mm should be
designed on the PCB between the edge of
the ePad and the inner edges of the lead
pads to avoid any electrical shorts.
Figure 30. ePad Diagram
The thermal land area on the PCB may use thermal vias to improve heat removal from the package. These
thermal vias can double as ground connections, attaching internally in the PCB to the ground plane. An array of
vias should be designed into the PCB beneath the package. For optimum thermal performance, it is
recommended that the via diameter should be 12 to 13 mils (0.30 to 0.33mm) and the via barrel should be plated
with 1 ounce copper to plug the via. This is desirable to avoid any solder wicking inside the via during the
soldering process, which may result in voids in solder between the exposed pad and the thermal land. If the
copper plating does not plug the vias, the thermal vias can be ‘tented’ with solder mask on the top surface of the
PCB to avoid solder wicking inside the via during assembly. The solder mask diameter should be at least 4 mils
(0.1mm) larger than the via diameter.
Package stand-off is also a consideration. For a nominal stand-off of 0.1mm (see Figure 32, dimension ‘A1’), the
stencil thickness of 5 to 8 mils should provide a good solder joint between the ePad and the thermal land. The
aperture opening should be subdivided into an array of smaller openings.
相關PDF資料
PDF描述
SiI1161CTU PanelLink Receiver
SII1162 PanelLink Transmitter
SII1169 PanelLink Receiver
SII1171 PanelLink Receiver
SII1172 PanelLink Transmitter
相關代理商/技術參數
參數描述
SII1161CTU 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver
SII1162 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Transmitter
SII1162CSU 制造商:Silicon Image Inc 功能描述:
SII1169 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver
SII1171 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*