- 您現在的位置：買賣IC網 > PDF目錄372122 > SC28C198A1A (NXP SEMICONDUCTORS) Octal UART for 3.3V and 5V supply voltage PDF資料下載
參數資料
| 型號： | SC28C198A1A |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Octal UART for 3.3V and 5V supply voltage |
| 中文描述： | 8 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC84 |
| 封裝： | PLASTIC, MO-047AF, SOT-189-3, LCC-84 |
| 文件頁數： | 27/56頁 |
| 文件大小： | 345K |
| 代理商： | SC28C198A1A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Philips Semiconductors
Product specification
SC28L198
Octal UART for 3.3V and 5V supply voltage
1999 Jan 14
27
Bits 7:6
Bits 5:4
Received X Character Sta-
tus
sion status
00 – none
01 – Xoff received
10 – Xon received
11 – both received
11 – Illegal, does not occur
ááááááááááááááááááááááááááááááá
ááááááááááááááááááááááááááááááá
á
ááááááááááááááááááááááááááááááá
á
á
áááááááááááááááááááááááááááááááá
XISR[7:6] –
Received X Character Status. This field can be read to
determine if the receiver has encountered an Xon or Xoff character
in the incoming data stream. These bits are maintained until a read
of the XISR. The field is updated by X character reception
regardless of the state of MR0(7, 3:2) or IMR(4). The field can
therefore be used as a character detector for the bit patterns stored
in the Xon and Xoff Character Registers.
á
Table 23. WDTRCR – Watch-dog Timer Enable
Register
Bit 6
Bit 5
Bit 4
h
g
f
e
1 on
0 off
0 off
0 off
0 off
receivers on the Octal UART.
Bits 3:2
á
á
Bits 1:0
á
00 – none
01 – Xon transmitted
10 – Xoff transmitted
á
áááááá
áááááá
Automatic X Character transmis-
áááááá
00 – normal
ááááááááá
ááááááááá
11 – Xon in pending
ááááááááá
00 – normal TxD data
á
á
á
á
á
á
á
XISR[5:4] –
Automatic transmission Status. This field indicates the
last flow control character sent in the Auto Receiver flow control
mode. If Auto Receiver mode has not been enabled, this field will
always read b’00. It will likewise reset to b’00 if MR0(3) is reset. If
the Auto Receiver mode is exited while this field reads b’10, it is the
user’s responsibility to transmit an Xon, when appropriate.
XISR[3:2] –
TxD flow Status. This field tracks the transmitter’s flow
status as follows:
00 – normal. The flow control is under host control.
01 – TxD halt pending. After the current character finishes the
transmitter will stop. The status will then change to b’00.
10 – re–enabled. The transmitter had been halted and restarted.
It is sending data characters. After a read of the XISR, it will
return to ”normal” status.
11 – disabled. The transmitter is flow controlled.
XISR[1:0] –
TxD character Status. This field allows determination of
the type of character being transmitted. If XISR(1:0) is b’01, the
channel is waiting for a data character to transfer from the TxFIFO.
This condition will only occur for a bit time after an Xon or Xoff
character transmission unless the TxFIFO is empty.
ááááááááááááááá
ááááááááááááááá
áááááááá
á
áááááá
áááááááááá
áááááááááá
d
1 on
0 off
c
1 on
0 off
b
1 on
0 off
a
1 on
0 off
á
á
1 on
á
1 on
á
1 on
á
á
á
á
Table 24. BRGTRU
–
BRG Timer Reload
Registers, Upper
Bits 7:0
8 MSB of the BRG Timer divisor.
ááááááááááááááááá
ááááááááááááááááá
This is the upper byte of the 16 bit value used by the BRG timer in
generating a baud rate clock
Table 25. BRGTRL
–
BRG Timer Reload
ááááááááááááááááá
ááááááááááááááááá
This is the lower byte of the 16 bit value used by the BRG timer in
generating a baud rate clock.
ááááááááááááááááá
BRGTCR b, Clock selection
0 – Resets the timer register and
holds it stopped
1 – Allows the timer register to
run.
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1b
111 – G
(1)
ááááááááááááááááááááááááááááááá
ááááááááááááááááááááááááááááááá
á
á
á
á
á
ááááááááááááááááááááááááááááááá
Start/Stop control and clock select register for the two BRG
counters. The clock selection is for the input to the counters. It is
that clock divided by the number represented by the BRGTU and
BRGTL the will be used as the 16x clock for the receivers and
transmitters. When the BRG timer Clock is selected for the
á
á
á
á
á
á
á
á
receiver(s) or transmitter(s) the receivers and transmitters will
consider it as a 16x clock and further device it by 16. In other words
the receivers and transmitters will always be in the 16x ode of
operation when the internal BRG timer is selected for their clock.
holds it stopped.
run.
á
á
á
á
(0)
ááááááááááááááááááááááááááááááá
ááááááá
ááááááá
ááááááá
áááááááá
áááááááá
áááááááá
áááááááá
áááááááá
ááááááá
ááááááá
ááááááá
ááááááá
ááááááá
á
á
001 – Sclk / 32
010 – Sclk/ 64
á
á
á
á
á
á
相關PDF資料 |
PDF描述 |
|---|---|
| SC28L202A1 | Dual universal asynchronous receiver/transmitter DUART |
| SC28L202 | Dual universal asynchronous receiver/transmitter DUART |
| SC28L202A1B | Dual universal asynchronous receiver/transmitter DUART |
| SC28L202A1D | Dual universal asynchronous receiver/transmitter DUART |
| SC431CS8DE2 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28C94 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad universal asynchronous receiver/transmitter QUART |
| SC28C94A1A | 功能描述:UART 接口集成電路 UART QUAD W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28C94A1A,512 | 功能描述:UART 接口集成電路 UART QUAD W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28C94A1A,518 | 功能描述:UART 接口集成電路 5V 4 CH UART IND TEMP RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28C94A1A | 制造商:NXP Semiconductors 功能描述:IC CMOS QUART SMD 28C94 PLCC52 |
發布緊急采購，3分鐘左右您將得到回復。