參數資料
型號： SC16C852SVIET
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
中文描述： 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PBGA36
封裝： 3.50 X 3.50 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SOT-912-1, TFBGA-36
文件頁數： 31/48頁
文件大小： 221K
代理商： SC16C852SVIET
SC16C852SV_1
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 01 — 23 September 2008
31 of 48
NXP Semiconductors
SC16C852SV
Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
7.14 Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register.
Bit 0 through bit 4 provide single or dual character software flow control selection. When
the Xon1 and Xon2 and/or Xoff1 and Xoff2 modes are selected, the double 8-bit words
are concatenated into two sequential numbers.
[1]
Enhanced function control bits: IER[7:4], ISR[5:4], FCR[5:4] and MCR[7:5].
Table 23.
Bit
7
Enhanced Feature Register bits description
Symbol
Description
EFR[7]
Automatic CTS flow control.
logic 0 = automatic CTS flow control is disabled (normal default condition)
logic 1 = enable automatic CTS flow control. Transmission will stop when CTS
goes to a logical 1. Transmission will resume when the CTS signal returns to a
logical 0.
EFR[6]
Automatic RTS flow control. Automatic RTS may be used for hardware flow
control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will be
generated when the receive FIFO is filled to the programmed trigger level and
RTS will go to a logic 1 at the next trigger level. RTS will return to a logic 0 when
data is unloaded below the next lower trigger level (programmed trigger level 1).
The state of this register bit changes with the status of the hardware flow control.
RTS functions normally when hardware flow control is disabled.
logic 0 = automatic RTS flow control is disabled (normal default condition)
logic 1 = enable automatic RTS flow control
EFR[5]
Special Character Detect.
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. The SC16C852SV compares each
incoming receive character with Xoff2 data. If a match exists, the received data
will be transferred to FIFO and ISR[4] will be set to indicate detection of special
character. Bit-0 in the X-registers corresponds with the LSB bit for the receive
character. When this feature is enabled, the normal software flow control must
be disabled (EFR[3:0] must be set to a logic 0).
EFR[4]
Enhanced function control bit. The content of IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] can be modified and latched. After modifying any bits in the enhanced
registers, EFR[4] can be set to a logic 0 to latch the new values. This feature
prevents existing software from altering or overwriting the SC16C852SV
enhanced functions.
logic 0 = disable/latch enhanced features
[1]
logic 1 = enables the enhanced functions
[1]
. When this bit is set to a logic 1, all
enhanced features of the SC16C852SV are enabled and user settings stored
during a reset will be restored.
EFR[3:0]
Cont-3:0 Tx, Rx control. Logic 0 or cleared is the default condition. Combinations
of software flow control can be selected by programming these bits. See
Table 24
.
6
5
4
3:0
Table 24.
Cont-3
0
1
0
Software flow control functions
[1]
Cont-2
Cont-1
0
X
0
X
1
X
Cont-0
X
X
X
TX, RX software flow controls
No transmit flow control
Transmit Xon1/Xoff1
Transmit Xon2/Xoff2
相關PDF資料
PDF描述
SC16C852VIET 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and XScale VLIO bus interface
SC16IS740IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS750IBS Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS750IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS760IBS Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
相關代理商/技術參數
參數描述
SC16C852SVIET,115 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C852SVIET,151 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C852SVIET,157 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C852V 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
SC16C852V_08 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V dual UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*