參數資料
型號： SC16C852SVIET
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
中文描述： 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PBGA36
封裝： 3.50 X 3.50 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SOT-912-1, TFBGA-36
文件頁數： 10/48頁
文件大?。?/td> 221K
代理商： SC16C852SVIET
SC16C852SV_1
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 01 — 23 September 2008
10 of 48
NXP Semiconductors
SC16C852SV
Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
SC16C852SV will suspend TX transmissions as soon as the stop bit of the character in
process is shifted out. Transmission is resumed after the CTSx input returns to a logic 0,
indicating more data may be sent.
When AFCR1[2] is set to 1, then the function of CTSx pin is mapped to the DSRx pin, and
the function of RTS is mapped to DTRx pin. DSRx and DTRx pins will behave as
described above for CTSx and RTSx.
With the automatic hardware flow control function enabled, an interrupt is generated when
the receive FIFO reaches the programmed trigger level. The RTSx (or DTRx) pin will not
be forced to a logic 1 (RTS off) until the receive FIFO reaches the next trigger level.
However, the RTSx (or DTRx) pin will return to a logic 0 after the receive buffer (FIFO) is
unloaded to the next trigger level below the programmed trigger level. Under the above
described conditions, the SC16C852SV will continue to accept data until the receive FIFO
is full.
When TXINTLVL, RXINTLVL, FLWCNTH and FLWCNTL in the First Extra Register Set
are all zeroes, the hardware and software flow control trigger levels are set by FCR[7:4];
see
Table 5
.
When either TXINTLVL, RXINTLVL, FLWCNTH or FLWCNTL in the First Extra Register
Set contains any value other than 0x00, the hardware and software flow control trigger
levels are set by FLWCNTH and FLWCNTL. The content in FLWCNTH determines how
many bytes are in the receive FIFO before RTSx (or DTRx) is de-asserted or XOFF is
sent. The content of FLWCNTL determines how many bytes are in the receive FIFO
before RTSx (or DTRx) is asserted, or XON is sent.
In 128-byte FIFO mode, hardware and software flow control trigger levels can be set to
any value between 1 and 128 in granularity of 1. The value of FLWCNTH should always
be greater than FLWCNTL. The UART does not check for this condition automatically, and
if this condition is not met spurious operation of the device might occur. When using
FLWCNTH and FWLCNTL, these registers must be initialized to the proper values before
hardware or software flow control is enabled via the EFR register.
6.6 Software flow control
When software flow control is enabled, the SC16C852SV compares one or two
sequentially received data characters with the programmed Xon or Xoff character
value(s). If the received character(s) match the programmed Xoff values, the
SC16C852SV will halt transmission (TX) as soon as the current character(s) has
completed transmission. When a match occurs, ISR bit 4 will be set (if enabled via IER[5])
and the interrupt output pin (if receive interrupt is enabled) will be activated. Following a
suspension due to a match of the Xoff characters’ values, the SC16C852SV will monitor
the receive data stream for a match to the Xon1/Xon2 character value(s). If a match is
found, the SC16C852SV will resume operation and clear the flags (ISR[4]).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to a logic 0.
Following reset, the user can write any Xon/Xoff value desired for software flow control.
Different conditions can be set to detect Xon/Xoff characters and suspend/resume
transmissions (see
Table 24
). When double 8-bit Xon/Xoff characters are selected, the
SC16C852SV compares two consecutive receive characters with two software flow
control 8-bit values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly.
相關PDF資料
PDF描述
SC16C852VIET 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and XScale VLIO bus interface
SC16IS740IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS750IBS Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS750IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS760IBS Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
相關代理商/技術參數
參數描述
SC16C852SVIET,115 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C852SVIET,151 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C852SVIET,157 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C852V 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
SC16C852V_08 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V dual UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*