- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C852SVIET (NXP SEMICONDUCTORS) 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface PDF資料下載
參數資料
| 型號： | SC16C852SVIET |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| 中文描述： | 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PBGA36 |
| 封裝： | 3.50 X 3.50 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SOT-912-1, TFBGA-36 |
| 文件頁數： | 27/48頁 |
| 文件大?。?/td> | 221K |
| 代理商： | SC16C852SVIET |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SC16C852SV_1
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 01 — 23 September 2008
27 of 48
NXP Semiconductors
SC16C852SV
Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 18.
Bit
7
Modem Control Register bits description
Symbol Description
MCR[7]
Clock select
logic 0 = divide-by-1 clock input
logic 1 = divide-by-4 clock input
MCR[6]
IR enable (see
Figure 15
).
logic 0 = enable the standard modem receive and transmit input/output interface
(normal default condition)
logic 1 = enable infrared IrDA receive and transmit inputs/outputs. While in this
mode, the TX/RX output/inputs are routed to the infrared encoder/decoder. The
data input and output levels will conform to the IrDA infrared interface
requirement. As such, while in this mode, the infrared TX output will be a logic 0
during idle data conditions.
MCR[5]
Reserved; set to ‘0’.
MCR[4]
Loopback. Enable the local Loopback mode (diagnostics). In this mode the
transmitter output (TX) and the receiver input (RX), CTS, DSR, CD, and RI are
disconnected from the SC16C852SV I/O pins. Internally the modem data and
control pins are connected into a loopback data configuration (see
Figure 7
). In
this mode, the receiver and transmitter interrupts remain fully operational. The
Modem Control Interrupts are also operational, but the interrupts’ sources are
switched to the lower four bits of the Modem Control. Interrupts continue to be
controlled by the IER register.
logic 0 = disable Loopback mode (normal default condition)
logic 1 = enable local Loopback mode (diagnostics)
MCR[3]
OP2A/OP2B, INT enable
logic 0 = forces INT (A, B) outputs to the 3-state mode (normal default condition)
logic 1 = forces the INT (A, B) outputs to the active mode
In Loopback mode, this bit is used to write the state of the modem CD interface
signal.
MCR[2]
This bit is used in the Loopback mode only. In the Loopback mode, this bit is used
to write the state of the modem RI interface signal.
MCR[1]
RTS
logic 0 = force RTS output to a logic 1 (normal default condition)
logic 1 = force RTS output to a logic 0
MCR[0]
DTR
logic 0 = force DTR output to a logic 1 (normal default condition)
logic 1 = force DTR output to a logic 0
6
5
4
3
2
1
0
Table 19.
MCR[3]
0
1
Interrupt output control
INT (A, B) output
3-state
active
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C852VIET | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and XScale VLIO bus interface |
| SC16IS740IPW | Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS750IBS | Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS750IPW | Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS760IBS | Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C852SVIET,115 | 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C852SVIET,151 | 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C852SVIET,157 | 功能描述:UART 接口集成電路 UART 2-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C852V | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface |
| SC16C852V_08 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V dual UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
發布緊急采購，3分鐘左右您將得到回復。