參數資料
型號： SC16C654BIBM
廠商： NXP Semiconductors N.V.
元件分類： 收發器
英文描述： 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
封裝： SC16C654BIA68<SOT188-2 (PLCC68)|<<http://www.nxp.com/packages/SOT188-2.html<1<Always Pb-free,;SC16C654BIA68<SOT188-2 (PLCC68)|<<http://www.nxp.com/packages/SOT188-2.html&
文件頁數： 27/58頁
文件大?。?/td> 302K
代理商： SC16C654BIBM
9397 750 14965
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 20 June 2005
27 of 58
Philips Semiconductors
SC16C654B/654DB
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO
trigger levels, and select the DMA mode.
7.3.1
DMA mode
7.3.1.1
Mode 0 (FCR bit 3 = 0)
Set and enable the interrupt for each single transmit or receive operation, and is similar to
the 16C454 mode. Transmit Ready (TXRDY) will go to a logic 0 whenever an empty
transmit space is available in the Transmit Holding Register (THR). Receive Ready
(RXRDY) will go to a logic 0 whenever the Receive Holding Register (RHR) is loaded with
a character.
7.3.1.2
Mode 1 (FCR bit 3 = 1)
Set and enable the interrupt in a block mode operation. The transmit interrupt is set when
the transmit FIFO is below the programmed trigger level. TXRDY remains a logic 0 as long
as one empty FIFO location is available. The receive interrupt is set when the receive
FIFO fills to the programmed trigger level. However, the FIFO continues to fill regardless
of the programmed level until the FIFO is full. RXRDY remains a logic 0 as long as the
FIFO fill level is above the programmed trigger level.
7.3.2
FIFO mode
Table 10:
Bit
7:6
FIFO Control Register bits description
Symbol
Description
FCR[7] (MSB),
FCR[6] (LSB)
FIFO interrupt.
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to
Table 11
.
FCR[5] (MSB),
FCR[4] (LSB)
These bits are used to set the trigger level for the transmit FIFO
interrupt. The SC16C654B/654DB will issue a transmit empty interrupt
when the number of characters in FIFO drops below the selected trigger
level. Refer to
Table 12
.
FCR[3]
DMA mode select.
logic 0 = set DMA mode ‘0’ (normal default condition)
logic 1 = set DMA mode ‘1’
Transmit operation in mode ‘0’:
When the SC16C654B/654DB is in
the 16C454 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO
mode (FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when
there are no characters in the transmit FIFO or transmit holding register,
the TXRDY pin will be a logic 0. Once active, the TXRDY pin will go to a
logic 1 after the first character is loaded into the transmit holding
register.
Receive operation in mode ‘0’:
When the SC16C654B/654DB is in
mode ‘0’ (FCR[0] = logic 0), or in the FIFO mode (FCR[0] = logic 1;
FCR[3] = logic 0) and there is at least one character in the receive FIFO,
the RXRDY pin will be a logic 0. Once active, the RXRDY pin will go to a
logic 1 when there are no more characters in the receiver.
RCVR trigger. These bits are used to set the trigger level for the receive
5:4
TX trigger.
3
相關PDF資料
PDF描述
SC16C654BIBS 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654DBIB64 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C750BIA44 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
SC16C750BIB64 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
SC16C750BIBS 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
相關代理商/技術參數
參數描述
SC16C654BIBM,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIBM,151 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIBM,157 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIBM151 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
SC16C654BIBM-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*