參數資料
型號： SC16C550BIB48
廠商： NXP Semiconductors N.V.
元件分類： 收發器
英文描述： 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
封裝： SC16C550BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 51, 2004,;SC16C550BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html&l
文件頁數： 25/48頁
文件大?。?/td> 240K
代理商： SC16C550BIB48
SC16C550B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 1 October 2008
25 of 48
NXP Semiconductors
SC16C550B
5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 19.
Bit
7
6
5
4
Modem Control Register bits description
Symbol
Description
MCR[7]
reserved; set to ‘0’
MCR[6]
reserved; set to ‘0’
MCR[5]
Auto flow control enable.
MCR[4]
Loopback. Enable the local loopback mode (diagnostics). In this mode the
transmitter output (TX) and the receiver input (RX), CTS, DSR, DCD, and
RI are disconnected from the SC16C550B I/O pins. Internally the modem
data and control pins are connected into a loopback data configuration
(see
Figure 11
). In this mode, the receiver and transmitter interrupts
remain fully operational. The Modem Control Interrupts are also
operational, but the interrupts’ sources are switched to the lower four bits
of the Modem Control. Interrupts continue to be controlled by the IER
register.
logic 0 = disable loopback mode (normal default condition)
logic 1 = enable local loopback mode (diagnostics)
MCR[3]
OUT2. Used to control the modem DCD signal in the loopback mode.
logic 0 = OUT2 is at logic 1. In the loopback mode, sets OUT2 (DCD)
internally to a logic 1.
logic 1 = OUT2 is at logic 0. In the loopback mode, sets OUT2 (DCD)
internally to a logic 0.
MCR[2]
OUT1. This bit is used in the Loopback mode only. In the loopback mode,
this bit is used to write the state of the modem RI interface signal via
OUT1.
MCR[1]
RTS
logic 0 = force RTS output to a logic 1 (normal default condition)
logic 1 = force RTS output to a logic 0
MCR[0]
DTR
logic 0 = force DTR output to a logic 1 (normal default condition)
logic 1 = force DTR output to a logic 0
3
2
1
0
相關PDF資料
PDF描述
SC16C550BIBS 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
SC16C650BIB48 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C650BIBS 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C652BIBS 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.) with 32-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654BIA68 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
相關代理商/技術參數
參數描述
SC16C550BIB48,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIB48,151 功能描述:UART 接口集成電路 1CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIB48,157 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIB48-S 功能描述:UART 接口集成電路 1CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIBS 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*