參數資料
型號： SAA7893HL
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： Super audio media player
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP128
封裝： 14 X 20 MM, 1.40 MM HEIGTH, PLASTIC, SOT-425-1, LQFP-128
文件頁數： 62/66頁
文件大小： 1036K
代理商： SAA7893HL
Philips Semiconductors
SAA7893HL
Super audio media player
Product data
Rev. 02 — 26 February 2003
62 of 66
9397 750 10925
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
18. Soldering
18.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
18.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferably be kept:
below 220
°
C for all the BGA packages and packages with a thickness
≥
2.5mm
and packages with a thickness <2.5 mm and a volume
≥
350 mm
3
so called
thick/large packages
below 235
°
C for packages with a thickness <2.5 mm and a volume <350 mm
3
so
called small/thin packages.
18.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
相關PDF資料
PDF描述
SAA8112HL Digital Camera Signal Processor and Microcontroller(數字照相信號處理器和微控制器)
SAA8113HL Digital PC-camera signal processor(數字PC照相信號處理器)
SAA8115HL Digital Camera USB Interface(數字照相USB接口)
SAA8116ET Digital PC-camera signal processor including microcontroller and USB interface
SAA8116HL Digital PC-camera signal processor, microcontroller andUSB interface
相關代理商/技術參數
參數描述
SAA-8 制造商:GENERAL DEVICES 功能描述:CHASSIS SUPPORT ANGLES, Sold in a Set of 2
SAA8110G 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Signal Processor DSP for cameras
SAA8112HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital camera signal processor and microcontroller
SAA8113HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital PC-camera signal processor
SAA8115HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital camera USB interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*