- 您現在的位置：買賣IC網 > PDF目錄372106 > SA58670 (NXP Semiconductors N.V.) 2.1 W/channel stereo Class D audio amplifier PDF資料下載
參數資料
| 型號： | SA58670 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 2.1 W/channel stereo Class D audio amplifier |
| 中文描述： | 2.1瓦/聲道立體聲D類音頻放大器 |
| 文件頁數： | 10/18頁 |
| 文件大小： | 142K |
| 代理商： | SA58670 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
SA58670_1
NXP B.V. 2007. All rights reserved.
Objective data sheet
Rev. 01 — 22 June 2007
10 of 18
NXP Semiconductors
SA58670
2.1 W/channel stereo Class D audio amplifier
11.3 PCB layout considerations
Component location is very important for performance of the SA58670. Place all external
components very close to the device. Placing decoupling capacitors directly at the power
supply pins increases efficiency because the resistance and inductance in the trace
between the device power supply pins and the decoupling capacitor causes a loss in
power efficiency.
The trace width and routing are also very important for power output and noise
considerations.
For high current terminals (PVDD, PGND and audio output), the trace widths should be
maximized to ensure proper performance and output power. Use at least 500
μ
m wide
traces.
For the input pins (INRP/INRN and INLP/INLN), the traces must be symmetrical and run
side-by-side to maximize common-mode cancellation.
11.4 Filter-free operation and ferrite bead filters
A ferrite bead low-pass filter can be used to reduce radio frequency emissions in
applications that have circuits sensitive to greater than 1 MHz. A ferrite bead low-pass
filter functions well for amplifiers that must pass FCC unintentional radiation requirements
at greater than 30 MHz. Choose a bead with high-impedance at high frequencies and very
low-impedance at low frequencies. In order to prevent distortion of the output signal,
select a ferrite bead with adequate current rating.
For applications in which there are circuits that are EMI sensitive to low frequency
(<1 MHz) and there are long leads from amplifier to speaker, it is necessary to use an LC
output filter.
11.5 Efficiency and thermal considerations
The maximum ambient operating temperature depends on the heat transferring ability of
the heat spreader on the PCB layout. In
Table 3 “Limiting values”
, power dissipation, the
power derating factor is given as 41.6 mW/
°
C. The device thermal resistance, R
th(j-a)
is the
reciprocal of the power derating factor. Convert the power derating factor to R
th(j-a)
by the
following equation:
(3)
For a maximum allowable junction temperature, T
j
= 150
°
C and R
th(j-a)
= 24
°
C/W and a
maximum device dissipation of 1.5 W (750 mW per channel) and for 2.1 W per channel
output power, 4
load, 5 V supply, the maximum ambient temperature is calculated using
Equation 4
:
(4)
The maximum ambient temperature is 114
°
C at maximum power dissipation for 5 V
supply and 4
load. If the junction temperature of the SA58670 rises above 150
°
C, the
thermal protection circuitry turns the device off; this prevents damage to IC. Using
speakers greater than 4
further enhances thermal performance and battery lifetime by
reducing the output load current and increasing amplifier efficiency.
R
th j
-
a
(
)
derating
factor
----------------------------------------
0.0413
---------------
24
°
C
/
W
=
=
=
T
amb max
)
T
j max
)
R
th j
-
a
(
)
P
D max
)
×
(
)
–
150
24
1.5
×
(
)
–
114
°
C
=
=
=
相關PDF資料 |
PDF描述 |
|---|---|
| SA58780 | Sense current amplifier with selectable gain |
| SA594 | Vacuum fluorescent display driver |
| SA594D | Vacuum fluorescent display driver |
| SA594F | Vacuum fluorescent display driver |
| SA594N | Vacuum fluorescent display driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA58670_08 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2.1 W/channel stereo class-D audio amplifier |
| SA58670A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2.1 W/channel stereo class-D audio amplifier |
| SA58670ABS | 制造商:NXP Semiconductors 功能描述:AMP AUDIO 2.1W STER D 20HVQFN 制造商:NXP Semiconductors 功能描述:AMP, AUDIO, 2.1W, STER, D, 20HVQFN |
| SA58670ABS,115 | 功能描述:音頻放大器 2.1W/CH CLASS D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58670ABS115 | 制造商:NXP Semiconductors 功能描述:IC AUDIO AMP D 2.1W QFN-20 |
發布緊急采購，3分鐘左右您將得到回復。