- 您現在的位置：買賣IC網 > PDF目錄192300 > S29PL127J70BFI000 (SPANSION LLC) 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 PDF資料下載
參數資料
| 型號： | S29PL127J70BFI000 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| 封裝： | 11 X 8 MM, LEAD FREE, FBGA-80 |
| 文件頁數： | 57/97頁 |
| 文件大?。?/td> | 3042K |
| 代理商： | S29PL127J70BFI000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
60
S29PL-J
S29PL-J_00_A10 September 7, 2007
Data
Sheet
(Adv an ce
Inf o r m a t io n)
Figure 15.1 Program Operation
Note
See Table 15.1 on page 64 for program command sequence.
15.6
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical erase. The system is not required to provide any
controls or timings during these operations. Table 15.1 on page 64 shows the address and data requirements
for the chip erase command sequence.
When the Embedded Erase algorithm is complete, that bank returns to the read mode and addresses are no
longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/
BY#. Refer to Write Operation Status on page 66 for information on these status bits.
Any commands written during the chip erase operation are ignored. Note that Secured Silicon Sector,
autoselect, and CFI functions are unavailable when a [program/erase] operation is in progress. However,
note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase
command sequence should be reinitiated once that bank has returned to reading array data, to ensure data
integrity.
Figure 15.2 on page 61 illustrates the algorithm for the erase operation. Refer to the tables in Erase/Program
Operations on page 78 for parameters, and Figure 20.8 on page 80 for timing diagrams.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data?
No
Yes
Last Address?
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料 |
PDF描述 |
|---|---|
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
| S2C3R-1-12-H | 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS |
| S2C5R-1-12-RC | 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
| S2H3R-1H | 10 MHz - 1000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.2 dB INSERTION LOSS |
| S2L1R-RC | 1000 MHz - 2000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 0.9 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL127J70TAI130 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI130 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI131 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Rail/Tube |
| S29PL127J70TFI132 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
| S29PL127J70TFI133 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。