參數資料
型號： S29PL127J70BFI000
廠商： SPANSION LLC
元件分類： PROM
英文描述： 8M X 16 FLASH 3V PROM, 70 ns, PBGA80
封裝： 11 X 8 MM, LEAD FREE, FBGA-80
文件頁數： 48/97頁
文件大?。?/td> 3042K
代理商： S29PL127J70BFI000
52
S29PL-J
S29PL-J_00_A10 September 7, 2007
Data
Sheet
(Adv an ce
Inf o r m a t io n)
13.5
Temporary Sector Unprotect
This feature allows temporary unprotection of previously protected sectors to change data in-system. The
Sector Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly protected
sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from the
RESET# pin, all the previously protected sectors are protected again. Figure 13.2 on page 52 shows the
algorithm, and Figure 21.1 on page 83 shows the timing diagrams, for this feature. While PPB lock is set, the
device cannot enter the Temporary Sector Unprotection Mode.
Figure 13.2 Temporary Sector Unprotect Operation
Notes:
1. All protected sectors unprotected (If WP#/ACC = VIL, upper two and lower two sectors will remain protected).
2. All previously protected sectors are protected once again
13.6
Secured Silicon Sector Flash Memory Region
The Secured Silicon Sector feature provides a Flash memory region that enables permanent part
identification through an Electronic Serial Number (ESN) The 128-word Secured Silicon sector is divided into
64 factory-lockable words that can be programmed and locked by the customer. The Secured Silicon sector
is located at addresses 000000h-00007Fh in both Persistent Protection mode and Password Protection
mode. Indicator bits DQ6 and DQ7 are used to indicate the factory-locked and customer locked status of the
part.
The system accesses the Secured Silicon Sector through a command sequence (see the Enter/Exit Secured
Silicon Sector Command Sequence on page 58). After the system has written the Enter Secured Silicon
Sector command sequence, it may read the Secured Silicon Sector by using the addresses normally
occupied by the boot sectors. This mode of operation continues until the system issues the Exit Secured
Silicon Sector command sequence, or until power is removed from the device. Once the Enter SecSi Sector
Command sequence has been entered, the standard array cannot be accessed until the Exit SecSi Sector
command has been entered or the device has been reset. On power-up, or following a hardware reset, the
device reverts to sending commands to the normal address space. Note that the ACC function and unlock
bypass modes are not available when the Secured Silicon Sector is enabled.
START
Perform Erase or
Program Operations
RESET# = VIH
Temporary Sector
Unprotect Completed
RESET# = VID
相關PDF資料
PDF描述
S29XS064R0PBHW010 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44
S2C3R-1-12-H 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS
S2C5R-1-12-RC 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS
S2H3R-1H 10 MHz - 1000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.2 dB INSERTION LOSS
S2L1R-RC 1000 MHz - 2000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 0.9 dB INSERTION LOSS
相關代理商/技術參數
參數描述
S29PL127J70TAI130 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays
S29PL127J70TFI130 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays
S29PL127J70TFI131 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Rail/Tube
S29PL127J70TFI132 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel
S29PL127J70TFI133 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*