- 您現在的位置：買賣IC網 > PDF目錄374647 > S2076 (Applied Micro Circuits Corp.) Quad Fibre Channel Transceiver(四光纖通道收發器) PDF資料下載
參數資料
| 型號： | S2076 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | Quad Fibre Channel Transceiver(四光纖通道收發器) |
| 中文描述： | 四光纖通道收發器（四光纖通道收發器） |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 300K |
| 代理商： | S2076 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
9
S2076
QUAD FIBRE CHANNEL TRANSCEIVER
October 13, 2000 / Revision B
e
d
o
M
E
D
O
M
C
.
e
r
F
x
0
C
B
R
e
d
o
M
k
c
o
C
f
H
0
z
H
M
5
2
1
5
e
d
o
M
k
c
o
C
l
F
1
z
H
M
5
2
0
1
Table 4. Output Clock Modes
Parallel Output Clock Rate
Two output clock modes are supported. When
CMODE is HIGH, a complementary TTL clock at the
data rate is provided on the RBC1/0x outputs. Data
should be clocked on the rising edge of RBC1x.
When CMODE is LOW, the S2076 outputs a
complementary TTL clock at 1/2 the data rate in
compliance with the Fibre Channel 10 Bit Interface
Specification. Data should be latched on the rising
edge of RBC1x and the rising edge of RBC0x.
If consecutive K28.5 characters are received, the
S2076 RBC1/0x clock operates without glitches or
loss of cycles.
OTHER OPERATING MODES
Loopback Mode
When loopback mode is enabled, the serial data
from the transmitter is provided to the serial input of
the receiver. Loopback mode can be simultaneously
enabled for all four channels using the loopback-en-
able input, LPEN.
The loopback mode provides the ability to perform
system diagnostics and off-line testing of the inter-
face to guarantee the integrity of the serial channel
before enabling the transmission medium. Loopback
is enabled when LPEN = 1.
Note that the high speed outputs are disabled during
loopback operation.
Test Modes
The RESET pin is used to initialize the Transmit
FIFOs and must be asserted (LOW) prior to entering
the normal operational state (see section Transmit
FIFO Initialization). Note that Reset does not disable
the TCLKO output unless the TBCB input is HIGH.
Operating Frequency Rate
The S2076 is designed to operate at the Fibre Chan-
nel rate of 1.062 GHz.
output
disabled
CRU
CSU
Figure 7. S2076 Diagnostic Loopback Operation
相關PDF資料 |
PDF描述 |
|---|---|
| S2078 | Dual Fibre Channel Transceiver(雙光纖通道收發器) |
| S2080 | 34×34 3.2 Gbit/s Differential Crosspoint Switch(高達3.2 Gbit/s數據傳送速率的34×34差分交叉開關) |
| S208T01 | Low Profile Type Solid State Relays |
| S208T02 | Low Profile Type Solid State Relays |
| S2091 | 2.5 Gbit Port Bypass Circuit for Fibre Channel Arbitrated Loop(用于光纖通道仲裁環路的端口旁路電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S2079 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Drivers for GaAs FET Switches and Digital Attenuators |
| S2079B1LF | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:ISDN S-INTERFACE DUAL TRANSFORMER MODULES SMLL SMT PACKAGE 23.5×12.3×9mm |
| S207R | 制造商:MINMAX 制造商全稱:Minmax Technology Co., Ltd. 功能描述:2W, Low Cost DIP, Single & Dual Output DC/DC Converters |
| S-208 | 制造商:SCANBE/VERO 功能描述: |
| S2080 | 制造商:Tyan 功能描述:MB;ATX;S370;PIIIT;SDRAM;SINGLE 制造商:Microsemi Corporation 功能描述:800V 16A 2PIN DO-203AA - Bulk |
發布緊急采購，3分鐘左右您將得到回復。