參數資料
型號： S1C88832F0A0100
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP128
封裝： PLASTIC, QFP-128
文件頁數： 155/160頁
文件大小： 1244K
代理商： S1C88832F0A0100
86
EPSON
S1C88832/88862 TECHNICAL MANUAL
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (Programmable Timer)
PLPOL: 00FF31HD5
Selects the pulse polarity for the K10 input port
terminal.
In event counter mode
When "1" is written: Rising edge
When "0" is written: Falling edge
Reading:
Valid
In the event counter mode, select whether the count
timing will be set at the falling edge of the external
clock (EVIN) input to the K10 input port terminal
or at the rising edge. When "0" is written to PLPOL,
the falling edge is selected and when "1" is written,
the rising edge is selected.
In pulse width measurement mode
When "1" is written: High level pulse width
measurement
When "0" is written: LOW level pulse width
measurement
Reading:
Valid
In the pulse width measurement mode, select
whether the LOW level width of the signal (EVIN)
input to the K10 input port terminal will be meas-
ured or the HIGH level will be measured. When "0"
is written to PLPOL, the LOW level width measure-
ment is selected and when "1" is written, the HIGH
level width measurement is selected.
In the normal mode (EVCNT = FCSEL = "0"), the
setting of PLPOL becomes invalid.
At initial reset, PLPOL is set to "0".
CONT0, CONT1: 00FF31HD2, 00FF32HD2
Select the continuous/one-shot mode.
When "1" is written: Continuous mode
When "0" is written: One-shot mode
Reading:
Valid
Select whether timer 0 will be used in the continu-
ous mode or in the one-shot mode.
By writing "1" to CONT0, the programmable timer is
set to the continuous mode. In the continuous mode,
the initial counter value is automatically loaded
when an underflow is generated, and counting is
continued. On the other hand, when writing "0" to
CONT0, the programmable timer is set to the one-
shot mode. The counter loads an initial value and
stops when an underflow is generated. At this time,
PRUN0 is automatically reset to "0".
In the same way, the continuous/one-shot mode
for timer 1 is selected by CONT1. (In the one-shot
mode for timer 1, PRUN1 is automatically reset to
"0" when the counter underflow is generated.)
At initial reset, this register is set to "0" (one-shot
mode).
RLD00–RLD07: 00FF33H
RLD10–RLD17: 00FF34H
Sets the initial value for the counter.
RLD00–RLD07:
Reload data for Timer 0
RLD10–RLD17:
Reload data for Timer 1
The reload data set in this register is loaded into the
respective counters and is counted down with that
as the initial value.
Reload data is loaded to the counter under two
conditions, when "1" is written to PSET0 or PSET1
and when the counter underflow automatically
loads.
At initial reset, this register is set to "FFH".
PTD00–PTD07: 00FF35H
PTD10–PTD17: 00FF36H
Data of the programmable timer can be read out.
PTD00–PTD07:
Timer 0 counter data
PTD10–PTD17:
Timer 1 counter data
These bits act as a buffer to maintain the counter
data during readout, and the data can be read as
optional timing. However, in the 16-bit mode, to
avoid a read error, (data error when a borrow from
timer 0 to timer 1 is generated in the middle of
reading PTD00–PTD07 and PTD10–PTD17),
PTD10–PTD17 latches the timer 1 counter data
according to the reading of PTD00–PTD07.
The latched status of PTD10–PTD17 is canceled
according to the readout of PTD10–PTD17 or when
0.73–1.22 msec (depends on the readout timing) has
elapsed. Therefore, in 16-bit mode, be sure to read
the counter data of PTD00–PTD07 and PTD10–
PTD17 in order.
Since these bits are exclusively for reading, the
write operation is invalid.
At initial reset, these bits are set to "FFH".
PSET0, PSET1: 00FF31HD1, 00FF32HD1
Presets the reload data to the counter.
When "1" is written: Preset
When "0" is written: No operation
Reading:
Always "0"
By writing "1" to PSET0, the reload data in PLD00–
PLD07 is preset to the counter of timer 0. When the
counter of timer 0 is preset in the RUN status, it
restarts immediately after presetting.
In the case of STOP status, the reload data that has
been preset is maintained.
No operation results when "0" is written.
In the same way, the reload data in PLD10–PLD17
is preset to the counter of timer 1 by PSET1.
When the 16-bit mode is selected, writing "1" to
PSET1 is invalid.
This bit is exclusively for writing, it always be-
comes "0" during reading.
相關PDF資料
PDF描述
S1C88848D0A0100 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192
S1C8F360F 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176
S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13305F00A 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13600F00A CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
相關代理商/技術參數
參數描述
S1C88848 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C8F360D411000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360D511000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F413100 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F513200 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*