- 您現在的位置：買賣IC網 > PDF目錄98052 > PIP201-12M-3,518 (NXP SEMICONDUCTORS) 200 A SWITCHING REGULATOR, PQCC68 PDF資料下載
參數資料
| 型號： | PIP201-12M-3,518 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 穩壓器 |
| 英文描述： | 200 A SWITCHING REGULATOR, PQCC68 |
| 封裝： | 10 X 10 MM, 0.85 MM HEIGHT, PLASTIC, SOT-687-1, HVQFN-68 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 345K |
| 代理商： | PIP201-12M-3,518 |
Philips Semiconductors
PIP201-12M-3
DC-to-DC converter powertrain
Product data
Rev. 03 — 19 November 2003
16 of 20
9397 750 11942
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
15.2 Rework guidelines
Since the solder joints are largely inaccessible, only the side llets can be touched
up. If there are defects underneath the package, then the whole package has to be
removed.
The rst step in component removal is to reow the solder joints. It is recommended
that the board is heated from the underside using a convective heater whilst hot air or
gas is directed at the upper surface of the component. Nozzles should be used to
direct the hot air or gas to minimize heating of adjacent components. Excessive
airow should be avoided since this may cause the package to skew. An airow
velocity of 15 to 20 liters per minute is usually adequate.
Once the solder joints have reowed, the component should be lifted off the board
using a vacuum pen.
The next step is to clean the solder pads using solder braid and a blade-style
soldering tool. Finally, the pads should be cleaned with a solvent. The solvent is
usually specic to the type of solder paste used in the original assembly and the
paste manufacturers recommendations should be followed.
16. Mounting
16.1 PCB design guidelines
The terminals on the underside of the package are rectangular in shape with a
rounded edge on the inside. Electrical connection between the package and the
printed-circuit board is made by printing solder paste onto the PCB footprint followed
by component placement and reow soldering. The PCB footprint shown in Figure 20
is designed to form reliable solder joints.
The use of solder resist between each solder land is recommended. PCB tracks
should not be routed through the corner areas shown in Figure 20. This is because
there is a small, exposed remnant of the leadframe in each corner of the package, left
over from the cropping process.
Good surface atness of the PCB lands is desirable to ensure accuracy of placement
after soldering. Printed-circuit boards that are nished with a roller tin process tend to
leave small lumps of tin in the corners of each land. Levelling with a hot air knife
improves atness. Alternatively, an electro-less silver or silver immersion process
produces completely at PCB lands.
相關PDF資料 |
PDF描述 |
|---|---|
| PIP201-12M | SPECIALTY ANALOG CIRCUIT, PQCC68 |
| PIP8000FHN/N1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 |
| PJ3843BCS | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| PJ3842BCD | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| PJ3842BCS | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIP202-12M | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC to DC converter powertrain |
| PIP202-12M-2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC-to-DC converter powertrain |
| PIP202-12M-2 /T3 | 功能描述:直流/直流開關轉換器 TAPE7 MOSFET RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PIP202-12M-2,518 | 功能描述:直流/直流開關調節器 TAPE7 MOSFET RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| PIP20-5,08 | 功能描述:可插拔接線端子 PCB Hdr, 45 Deg, 5,08 PitchClosed End,20pole,12A,300V,Grn RoHS:否 制造商:Phoenix Contact 產品:Plugs 系列:PTS 端接類型:Spring Cage 位置/觸點數量:5 線規量程:26-14 節距:5 mm 電流額定值:10 A 電壓額定值:250 V 安裝風格: 安裝角: 觸點電鍍: |
發布緊急采購，3分鐘左右您將得到回復。