- 您現在的位置：買賣IC網 > PDF目錄98052 > PIP201-12M-3,518 (NXP SEMICONDUCTORS) 200 A SWITCHING REGULATOR, PQCC68 PDF資料下載
參數資料
| 型號： | PIP201-12M-3,518 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 穩壓器 |
| 英文描述： | 200 A SWITCHING REGULATOR, PQCC68 |
| 封裝： | 10 X 10 MM, 0.85 MM HEIGHT, PLASTIC, SOT-687-1, HVQFN-68 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 345K |
| 代理商： | PIP201-12M-3,518 |
Philips Semiconductors
PIP201-12M-3
DC-to-DC converter powertrain
Product data
Rev. 03 — 19 November 2003
12 of 20
9397 750 11942
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
printed-circuit board is approximately 5 K/W. In order to take full advantage of the low
thermal resistance of this package, the printed-circuit board must be designed so that
heat is conducted away efciently from the package. This can be achieved by
maximizing the area of copper around each pad, and by incorporating thermal vias to
conduct the heat to inner and/or bottom layers of the printed-circuit board.
An example of a thermal via pattern is shown in Figure 13. In a typical application,
with no forced air cooling, the use of thermal vias typically reduces the thermal
resistance from 25 K/W to 20 K/W. The additional use of a small fan can reduce this
further to approximately 15 K/W.
The thermal resistance of a particular design can be measured by passing a known
current through the source-drain diode of the lower MOSFET. The direction of current
ow is into VSSO and out of VO. The volt drop between VSSO and VO is then measured
and used to calculate the power dissipation in the PIP201-12M. The case
temperature of the PIP201-12M can be measured using an infra-red thermometer.
The thermal resistance can then be calculated using the following equation:
(3)
where Tcase is the measured case temperature (°C), Tamb is the ambient
temperature (
°C), I is the MOSFET current (A), and VF is the voltage drop between
VSSO and VDDO (V).
Where more than one phase is used, for example the circuit of Figure 11, the thermal
resistance of each PIP201-12M should be measured with current owing in all
phases.
12. Test information
Figure 14 shows the test circuit used to measure power loss in the PIP201-12M. The
output voltage is measured using an averaging circuit. This eliminates losses in the
output inductor and the PCB tracks. The calculated power loss, using this method,
All holes 0.5 mm diameter with 1 mm spacing.
Fig 13. Printed-circuit board thermal via pattern.
03ag36
PAD1
PAD2
PAD3
R
th j
pcb
–
()
T
case
T
amb
–
IV
F
×
------------------------------- KW
()
=
相關PDF資料 |
PDF描述 |
|---|---|
| PIP201-12M | SPECIALTY ANALOG CIRCUIT, PQCC68 |
| PIP8000FHN/N1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 |
| PJ3843BCS | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| PJ3842BCD | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| PJ3842BCS | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIP202-12M | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC to DC converter powertrain |
| PIP202-12M-2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC-to-DC converter powertrain |
| PIP202-12M-2 /T3 | 功能描述:直流/直流開關轉換器 TAPE7 MOSFET RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PIP202-12M-2,518 | 功能描述:直流/直流開關調節器 TAPE7 MOSFET RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| PIP20-5,08 | 功能描述:可插拔接線端子 PCB Hdr, 45 Deg, 5,08 PitchClosed End,20pole,12A,300V,Grn RoHS:否 制造商:Phoenix Contact 產品:Plugs 系列:PTS 端接類型:Spring Cage 位置/觸點數量:5 線規量程:26-14 節距:5 mm 電流額定值:10 A 電壓額定值:250 V 安裝風格: 安裝角: 觸點電鍍: |
發布緊急采購，3分鐘左右您將得到回復。