- 您現在的位置：買賣IC網 > PDF目錄368020 > PI7C8152B PCI Bridge | Asynchronous 2-Port PCI Bridge PDF資料下載
參數資料
| 型號： | PI7C8152B |
| 英文描述： | PCI Bridge | Asynchronous 2-Port PCI Bridge |
| 中文描述： | PCI橋|異步2端口PCI橋 |
| 文件頁數： | 75/115頁 |
| 文件大?。?/td> | 879K |
| 代理商： | PI7C8152B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
PI7C8150B
2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 75 of 115
July 31, 2003 – Revision 1.031
The data is input through the dedicated input signal, MSK_IN.
The shift register circuitry is not necessary for correct operation of PI7C8150B. The shift
register can be eliminated, and MSK_IN can be tied LOW to enable all secondary clock
outputs or tied HIGH to force all secondary clock outputs HIGH. Table 10-2 shows the
format of the serial stream.
Table 10-2. GPIO Serial Data Format
Bit
Description
S_CLKOUT
[1:0]
[3:2]
[5:4]
[7:6]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
Slot 0 PRSNT#[1:0] or device 0
Slot 1 PRSNT#[1:0] or device 1
Slot 2 PRSNT#[1:0] or device 2
Slot 3 PRSNT#[1:0] or device 3
Device 4
Device 5
Device 6
Device 7
Device 8
PI7C8150B S_CLKIN
Reserved
Reserved
0
1
2
3
4
5
6
7
8
9
NA
NA
The first 8 bits contain the PRSNT#[1:0] signal values for four slots, and these bits control
the S_CLKOUT[3:0] outputs. If one or both of the PRSNT#[1:0] signals are 0, that
indicates that a card is present in the slot and therefore the secondary clock for that slot is
not masked. If these clocks are connected to devices and not to slots, one or both of the bits
should be tied low to enable the clock.
The next 5 bits are the clock mask for devices; each bit enables or disables the clock for
one device. These bits control the S_CLKOUT[8:4] outputs: 0 enables the clock, and 1
disables the clock.
Bit 13 is the clock enable bit for S_CLKOUT[9], which is connected to PI7C8150B’s
S_CLKIN input.
If desired, the assignment of S_CLKOUT outputs to slots, devices, and PI7C8150B’s
S_CLKIN input can be rearranged from the assignment shown here. However, it is
important that the serial data stream format match the assignment of S_CLKOUT.
The 8 least significant bits are connected to the PRSNT# pins for the slots. The next 5 bits
are tied high to disable their respective secondary clocks because those clocks are not
connected to anything. The next bit is tied LOW because that secondary clock output is
connected to the PI7C8150B S_CLKIN input. When the secondary reset signal, S_RST_L,
is detected asserted and the primary reset signal, P_RST_L, is detected deasserted,
PI7C8150B drives GPIO[2] LOW for one cycle to load the clock mask inputs into the shift
register. On the next cycle, PI7C8150B drives GPIO[2] HIGH to perform a shift operation.
This shifts the clock mask into MSK_IN; the most significant bit is shifted in first, and the
least significant bit is shifted in last.
After the shift operation is complete, PI7C8150B tri-states the GPIO signals and can
deassert S_RST_L if the secondary reset bit is clear. PI7C8150B then ignores MSK_IN.
Control of the GPIO signal now reverts to PI7C8150B GPIO control registers. The clock
disable mask can be modified subsequently through a configuration write command to the
secondary clock control register in device-specific configuration space.
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C8154 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8154-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150-33 | PCI Bridge | 2-Port PCI-to-PCI Bridge |
| PI7C8150A | PCI Bridge | 2-Port PCI-to-PCI Bridge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8152BEVB | 功能描述:界面開發工具 2 Port PCI to PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C8152BMA | 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 160-Pin MQFP |
| PI7C8152BMAE | 功能描述:外圍驅動器與原件 - PCI PCI -to -PCI Bridge 2 Port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8152BMAIE | 功能描述:外圍驅動器與原件 - PCI 2 Port PCI to PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8154 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Bridge | 2-Port PCI-to-PCI Bridge |
發布緊急采購，3分鐘左右您將得到回復。