參數資料
型號： P89V662FBC,557
廠商： NXP Semiconductors
文件頁數： 47/90頁
文件大小： 0K
描述： IC 80C51 MCU FLASH 32K 44-TQFP
產品培訓模塊： Migrating from 8/16-Bit MCUs to 32-Bit ARMs
標準包裝： 800
系列： 89V
核心處理器： 8051
芯體尺寸： 8-位
速度： 40MHz
連通性： I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 36
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-TQFP
包裝： 托盤
配用： 622-1001-ND - USB IN-CIRCUIT PROG 80C51ISP
其它名稱： 568-2435
568-2435-ND
568-8271
935280832557
P89V662FBC
P89V660_662_664
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3.1 — 17 October 2011
51 of 90
NXP Semiconductors
P89V660/662/664
80C51 with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the
following conditions are met at the time the final shift pulse is generated: (a) RI = 0, and
(b) Either SM2 = 0, or the received 9th data bit = 1.
If either of these conditions is not met, the received frame is irretrievably lost, and RI is not
set. If both conditions are met, the received 9th data bit goes into RB8, and the first 8 data
bits go into SBUF.
6.7.8 Multiprocessor communications
UART modes 2 and 3 have a special provision for multiprocessor communications. In
these modes, 9 data bits are received or transmitted. When data is received, the 9th bit is
stored in RB8. The UART can be programmed so that when the stop bit is received, the
serial port interrupt will be activated only if RB8 = 1. This feature is enabled by setting bit
SM2 in SCON. One way to use this feature in multiprocessor systems is as follows:
When the master processor wants to transmit a block of data to one of several slaves, it
first sends out an address byte which identifies the target slave. An address byte differs
from a data byte in a way that the 9th bit is ‘1’ in an address byte and ‘0’ in the data byte.
With SM2 = 1, no slave will be interrupted by a data byte, i.e. the received 9th bit is ‘0’.
However, an address byte having the 9th bit set to ‘1’ will interrupt all slaves, so that each
slave can examine the received byte and see if it is being addressed or not. The
addressed slave will clear its SM2 bit and prepare to receive the data (still 9 bits long) that
follow. The slaves that weren’t being addressed leave their SM2 bits set and go on about
their business, ignoring the subsequent data bytes.
SM2 has no effect in Mode 0, and in Mode 1 can be used to check the validity of the stop
bit, although this is better done with the Framing Error flag. When UART receives data in
mode 1 and SM2 = 1, the receive interrupt will not be activated unless a valid stop bit is
received.
6.7.9 Automatic address recognition
Automatic address recognition is a feature which allows the UART to recognize certain
addresses in the serial bit stream by using hardware to make the comparisons. This
feature saves a great deal of software overhead by eliminating the need for the software
to examine every serial address which passes by the serial port. This feature is enabled
for the UART by setting the SM2 bit in SCON. In the 9 bit UART modes, mode 2 and mode
3, the Receive Interrupt flag (RI) will be automatically set when the received byte contains
either the ‘Given’ address or the ‘Broadcast' address. The 9 bit mode requires that the 9th
information bit is a ‘1’ to indicate that the received information is an address and not data.
Using the automatic address recognition feature allows a master to selectively
communicate with one or more slaves by invoking the Given slave address or addresses.
All of the slaves may be contacted by using the Broadcast address. Two special function
registers are used to define the slave’s address, SADDR, and the address mask, SADEN.
SADEN is used to define which bits in the SADDR are to be used and which bits are ‘don’t
care’. The SADEN mask can be logically ANDed with the SADDR to create the Given
address which the master will use for addressing each of the slaves. Use of the Given
address allows multiple slaves to be recognized while excluding others.
This device uses the methods presented in Figure 22 to determine if a Given or Broadcast
address has been received or not.
相關PDF資料
PDF描述
PIC32MX130F064B-I/SO IC MCU 32BIT 64KB FLASH 28-SOIC
PIC32MX220F032D-I/ML IC MCU 32BIT 32KB FLASH 44QFN
PIC18LF26K80-I/MM MCU PIC 64KB FLASH 28QFN
PIC18F26K80-I/MM MCU PIC 64KB FLASH 28QFN
PIC16C55-RC/P IC MCU OTP 512X12 28DIP
相關代理商/技術參數
參數描述
P89V664 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V664FA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V664FA,512 功能描述:8位微控制器 -MCU 80C51 64K FL / 2K RM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89V664FA512 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V664FBC 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*