- 您現在的位置：買賣IC網 > PDF目錄296762 > P89LPC938FDH (NXP Semiconductors N.V.) 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A-D converter PDF資料下載
參數資料
| 型號： | P89LPC938FDH |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A-D converter |
| 封裝： | P89LPC938FDH<SOT361-1 (TSSOP28)|<<http://www.nxp.com/packages/SOT361-1.html<1<Always Pb-free,;P89LPC938FHN<SOT788-1 (HVQFN28)|<<http://www.nxp.com/packages/SOT788-1.html& |
| 文件頁數： | 43/68頁 |
| 文件大?。?/td> | 318K |
| 代理商： | P89LPC938FDH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
9397 750 14051
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 25 February 2005
48 of 68
Philips Semiconductors
P89LPC938
8-bit microcontroller with 10-bit A/D converter
after the remaining input channels have been converted. After all selected channels have
been converted, the process will repeat starting with the rst selected channel. Additional
conversion results will again cycle through the eight result register pairs, overwriting the
previous results.Continous conversions continue until terminated by the user.
8.4.5 Dual channel, continuous conversion mode
This is a variation of the auto scan continuous conversion mode where conversion occurs
on two user-selectable inputs. The result of the conversion of the rst channel is placed in
the result register pair, AD0DAT0R and AD0DAT0L. The result of the conversion of the
second channel is placed in result register pair, AD0DAT1R and AD0DAT1L. The rst
channel is again converted and its result stored in AD0DAT2R and AD0DAT2L. The
second channel is again converted and its result placed in AD0DAT3R and AD0DAT3L,
etc. An interrupt is generated, if enabled, after every set of four or eight conversions (user
selectable).
8.4.6 Single step mode
This special mode allows ‘single-stepping’ in an auto scan conversion mode. Any
combination of the eight input channels can be selected for conversion. After each
channel is converted, an interrupt is generated, if enabled, and the A/D waits for the next
start condition. May be used with any of the start modes.
8.5 Conversion start modes
8.5.1 Timer triggered start
An A/D conversion is started by the overow of Timer 0. Once a conversion has started,
additional Timer 0 triggers are ignored until the conversion has completed. The Timer
triggered start mode is available in all A/D operating modes.
8.5.2 Start immediately
Programming this mode immediately starts a conversion.This start mode is available in all
A/D operating modes.
8.5.3 Edge triggered
An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has
started, additional edge triggers are ignored until the conversion has completed. The edge
triggered start mode is available in all A/D operating modes.
8.6 Boundary limits interrupt
The A/D converter has both a high and low boundary limit register. The user may select
whether an interrupt is generated when the conversion result is within (or equal to) the
high and low boundary limits or when the conversion result is outside the boundary limits.
An interrupt will be generated, if enabled, if the result meets the selected interrupt criteria.
The boundary limit may be disabled by clearing the boundary limit interrupt enable.
An early detection mechanism exists when the interrupt criteria has been selected to be
outside the boundary limits. In this case, after the four MSBs have been converted, these
four bits are compared with the four MSBs of the boundary high and low registers. If the
four MSBs of the conversion meet the interrupt criteria (i.e., outside the boundary limits)
an interrupt will be generated, if enabled. If the four MSBs do not meet the interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| P8 | HERMAPHRODITIC, STRAIGHT BOARD STACKING CONNECTOR, SURFACE MOUNT |
| PA33 | Operational Amplifier |
| PA33A | Operational Amplifier |
| PA35WPF | KLEMMLEISTE KABELSCHUTZ 12POL 380VAC 6A |
| PA35 | Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC938FDH,529 | 功能描述:8位微控制器 -MCU 80C51 8K FL 768B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC938FDH529 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ TSSOP-28 |
| P89LPC938FHN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
| P89LPC938FHN,151 | 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC938FHN-S | 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。