- 您現在的位置：買賣IC網 > PDF目錄296762 > P89LPC938FDH (NXP Semiconductors N.V.) 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A-D converter PDF資料下載
參數資料
| 型號： | P89LPC938FDH |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A-D converter |
| 封裝： | P89LPC938FDH<SOT361-1 (TSSOP28)|<<http://www.nxp.com/packages/SOT361-1.html<1<Always Pb-free,;P89LPC938FHN<SOT788-1 (HVQFN28)|<<http://www.nxp.com/packages/SOT788-1.html& |
| 文件頁數： | 40/68頁 |
| 文件大小： | 318K |
| 代理商： | P89LPC938FDH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
9397 750 14051
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 25 February 2005
45 of 68
Philips Semiconductors
P89LPC938
8-bit microcontroller with 10-bit A/D converter
In addition, IAP operations can be accomplished through the use of four SFRs consisting
of a control/status register, a data register, and two address registers. Additional details
may be found in the
P89LPC938 User’s Manual.
7.28.8 ISP
In-System Programming is performed without removing the microcontroller from the
system. The In-System Programming facility consists of a series of internal hardware
resources coupled with internal rmware to facilitate remote programming of the
P89LPC938 through the serial port. This rmware is provided by Philips and embedded
within each P89LPC938 device. The Philips In-System Programming facility has made
in-system programming in an embedded application possible with a minimum of additional
expense in components and circuit board area. The ISP function uses ve pins (VDD,VSS,
TXD, RXD, and RST). Only a small connector needs to be available to interface your
application to an external circuit in order to use this feature.
7.28.9 Power-on reset code execution
The P89LPC938 contains two special Flash elements: the Boot Vector and the Boot
Status Bit. Following reset, the P89LPC938 examines the contents of the Boot Status Bit.
If the Boot Status Bit is set to zero, power-up execution starts at location 0000H, which is
the normal start address of the user’s application code. When the Boot Status Bit is set to
a value other than zero, the contents of the Boot Vector is used as the high byte of the
execution address and the low byte is set to 00H.
Table 8 shows the factory default Boot Vector setting for this device. A factory-provided
boot loader is pre-programmed into the address space indicated and uses the indicated
boot loader entry point to perform ISP functions. This code can be erased by the user.
Users who wish to use this loader should take precautions to avoid erasing the
1 kB sector that contains this boot loader. Instead, the page erase function can be
used to erase the rst eight 64-byte pages located in this sector. A custom boot
loader can be written with the Boot Vector set to the custom boot loader, if desired.
7.28.10 Hardware activation of the boot loader
The boot loader can also be executed by forcing the device into ISP mode during a
power-on sequence (see the
P89LPC938 User’s Manual for specic information). This
has the same effect as having a non-zero status byte. This allows an application to be built
that will normally execute user code but can be manually forced into ISP operation. If the
factory default setting for the Boot Vector (1FH) is changed, it will no longer point to the
factory pre-programmed ISP boot loader code. After programming the Flash, the status
byte should be programmed to zero in order to allow execution of the user’s application
code beginning at address 0000H.
Table 8:
Default Boot Vector values and ISP entry points
Device
Default
Boot Vector
Default
boot loader
entry point
Default boot loader
code range
1 kB sector
range
P89LPC938
1FH
1F00H
1E00H to 1FFFH
1C00H to 1FFFH
相關PDF資料 |
PDF描述 |
|---|---|
| P8 | HERMAPHRODITIC, STRAIGHT BOARD STACKING CONNECTOR, SURFACE MOUNT |
| PA33 | Operational Amplifier |
| PA33A | Operational Amplifier |
| PA35WPF | KLEMMLEISTE KABELSCHUTZ 12POL 380VAC 6A |
| PA35 | Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC938FDH,529 | 功能描述:8位微控制器 -MCU 80C51 8K FL 768B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC938FDH529 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ TSSOP-28 |
| P89LPC938FHN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
| P89LPC938FHN,151 | 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC938FHN-S | 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。