- 您現在的位置：買賣IC網 > PDF目錄369945 > P89LPC932BA (NXP SEMICONDUCTORS) 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM PDF資料下載
參數資料
| 型號： | P89LPC932BA |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
| 中文描述： | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQCC28 |
| 封裝： | PLASTIC, MS-018, SOT-261-2, LCC-28 |
| 文件頁數： | 26/64頁 |
| 文件大?。?/td> | 316K |
| 代理商： | P89LPC932BA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
9397 750 14871
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 10 May 2005
26 of 64
Philips Semiconductors
P89LPC932A1
8-bit microcontroller with accelerated two-clock 80C51 core
After power-up this input will function either as an external reset input or as a digital input
as defined by the RPE bit. Only a power-up reset will temporarily override the selection
defined by RPE bit. Other sources of reset will not override the RPE bit.
Reset can be triggered from the following sources:
External reset pin (during power-up or if user configured via UCFG1).
Power-on detect.
Brownout detect.
Watchdog timer.
Software reset.
UART break character detect reset.
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
For any other reset, previously set flag bits that have not been cleared will remain set.
7.16.1
Reset vector
Following reset, the P89LPC932A1 will fetch instructions from either address 0000H or
the Boot address. The Boot address is formed by using the Boot Vector as the high byte of
the address and the low byte of the address = 00H.
The Boot address will be used if a UART break reset occurs, or the non-volatile Boot
Status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on (see
P89LPC932A1 User manual). Otherwise, instructions will be fetched from address 0000H.
7.17 Timers/counters 0 and 1
The P89LPC932A1 has two general purpose counter/timers which are upward compatible
with the standard 80C51 Timer 0 and Timer 1. Both can be configured to operate either as
timers or event counter. An option to automatically toggle the T0 and/or T1 pins upon timer
overflow has been added.
In the ‘Timer’ function, the register is incremented every machine cycle.
In the ‘Counter’ function, the register is incremented in response to a 1-to-0 transition at its
corresponding external input pin, T0 or T1. In this function, the external input is sampled
once during every machine cycle.
Timer 0 and Timer 1 have five operating modes (modes 0, 1, 2, 3 and 6). Modes 0, 1, 2
and 6 are the same for both Timers/Counters. Mode 3 is different.
7.17.1
Mode 0
Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit
Counter with a divide-by-32 prescaler. In this mode, the Timer register is configured as a
13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC932BDH | 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
| P89LPC932FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM |
| P89LPC932FHN | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM |
| P89LPC932A1FA | 8-Bit Microcontroller with accelerated two-clock 80C51 core 8kB 3V byte-erasable flash with 512-byte data EEPROM |
| P8N18 | N-CHANNEL LOGIC LEVEL POWER FIELD EFFECT TRANSISTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC932BDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM |
| P89LPC932FDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM |
| P89LPC932FDH.529 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 8K FLASH SMD 89LC932 |
| P89LPC932FDH/CP3235, | 制造商:NXP Semiconductors 功能描述:MICRO CONTROLLER(MCU |
| P89LPC932FHN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM |
發布緊急采購，3分鐘左右您將得到回復。