參數資料
型號： P89LPC932BA
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM
中文描述： 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQCC28
封裝： PLASTIC, MS-018, SOT-261-2, LCC-28
文件頁數： 24/64頁
文件大?。?/td> 316K
代理商： P89LPC932BA
9397 750 14871
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 10 May 2005
24 of 64
Philips Semiconductors
P89LPC932A1
8-bit microcontroller with accelerated two-clock 80C51 core
7.13.1.4
Push-pull output configuration
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a Schmitt
trigger input that also has a glitch suppression circuit.
7.13.2
Port 0 analog functions
The P89LPC932A1 incorporates two Analog Comparators. In order to give the best
analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-only (high-impedance)
mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
7.13.3
Additional port features
After power-up, all pins are in Input-only mode.
Please note that this is different from
the LPC76x series of devices.
After power-up, all I/O pins except P1.5, may be configured by software.
Pin P1.5 is input only. Pins P1.2 and P1.3 and are configurable for either input-only or
open-drain.
Every output on the P89LPC932A1 has been designed to sink typical LED drive current.
However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to
Table 9 “Static characteristics”
for detailed specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
7.14 Power monitoring functions
The P89LPC932A1 incorporates power monitoring functions designed to prevent
incorrect operation during initial power-up and power loss or reduction during operation.
This is accomplished with two hardware functions: Power-on detect and brownout detect.
7.14.1
Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a brownout detection to cause a processor reset,
however it may alternatively be configured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If brownout detection is the brownout condition occurs when V
DD
falls below the brownout
trip voltage, V
bo
(see
Table 9 “Static characteristics”
), and is negated when V
DD
rises
above V
bo
. If the P89LPC932A1 device is to operate with a power supply that can be
below 2.7 V, BOE should be left in the unprogrammed state so that the device can operate
at 2.4 V, otherwise continuous brownout reset may prevent the device from operating.
相關PDF資料
PDF描述
P89LPC932BDH 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM
P89LPC932FDH 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM
P89LPC932FHN 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM
P89LPC932A1FA 8-Bit Microcontroller with accelerated two-clock 80C51 core 8kB 3V byte-erasable flash with 512-byte data EEPROM
P8N18 N-CHANNEL LOGIC LEVEL POWER FIELD EFFECT TRANSISTORS
相關代理商/技術參數
參數描述
P89LPC932BDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM
P89LPC932FDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM
P89LPC932FDH.529 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 8K FLASH SMD 89LC932
P89LPC932FDH/CP3235, 制造商:NXP Semiconductors 功能描述:MICRO CONTROLLER(MCU
P89LPC932FHN 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*