- 您現在的位置：買賣IC網 > PDF目錄369944 > P89LPC917 (NXP Semiconductors N.V.) 8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter PDF資料下載
參數資料
| 型號： | P89LPC917 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter |
| 中文描述： | 8 - 8加速雙位單片機80C51的時鐘核心2 Kb的3伏閃存位A / D轉換器 |
| 文件頁數： | 9/72頁 |
| 文件大?。?/td> | 344K |
| 代理商： | P89LPC917 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Product data
Rev. 04 — 17 December 2004
9 of 72
9397 750 14397
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
P1.0 to P1.5
I/O
(P1.2);
I (P1.5)
Port 1:
Port 1 is a 6-bit I/O port with user-configurable outputs. During reset Port 1
latches are configured in the input only mode with the internal pull-up disabled. The
operation of the inputs and outputs depends upon the port configuration selected.
Refer to
Section 9.12.1 “Port configurations”
and
Table 13 “DC electrical
characteristics”
for details. P1.2 is an open drain when used as an output. P1.5 is
input only.
All pins have Schmitt triggered inputs.
Port 1 also provides various special functions as described below:
P1.0 —
Port 1 bit 0
TxD —
Serial port transmitter data.
P1.1 —
Port 1 bit 0
RxD —
Serial port receiver data.
P1.2 —
Port 1 bit 2. (Open drain when used as an output.)
T0 —
Timer/counter 0 external count input, overflow output, or PWM output.
SCL —
I
2
C-bus serial clock input/output.
P1.3 —
Port 1 bit 2. (Open drain when used as an output.)
INT0 —
External interrupt 0 input.
SDA —
I
2
C-bus serial data input/output.
P1.4 —
Port 1 bit 2.
INT1 —
External interrupt 1input.
P1.5 —
Port 1 bit 5. (Input only.)
RST —
External Reset input during power-on or if selected via UCFG1. When
functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O
ports and peripherals to take on their default states, and the processor begins
execution at address 0.
When using an oscillator frequency above 12 MHz, the
reset input function of P1.5 must be enabled. An external circuit is required to
hold the device in reset at power-up until V
DD
has reached its specified level.
When system power is removed V
DD
will fall below the minimum specified
operating voltage. When using an oscillator frequency above 12 MHz, in some
applications, an external brownout detect circuit may be required to hold the
device in reset when V
DD
falls below the minimum specified operating voltage.
Also used during a power-on sequence to force In-System Programming mode.
Ground:
0 V reference.
Power Supply:
This is the power supply voltage for normal operation as well as Idle
and Power-down modes.
9
I/O
O
I/O
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
8
7
6
5
3
V
SS
V
DD
4
10
I
I
Table 3:
Symbol
P89LPC915 pin description
…continued
Pin
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC932A1 | 8-Bit Microcontroller with accelerated two-clock 80C51 core 8kB 3V byte-erasable flash with 512-byte data EEPROM |
| P89LPC932 | 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
| P89LPC932BA | 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
| P89LPC932BDH | 80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
| P89LPC932FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC9171 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core, 2 kB 3 V byte-erasable flash with 8-bit ADC |
| P89LPC9171FDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core, 2 kB 3 V byte-erasable flash with 8-bit ADC |
| P89LPC9171FDH,129 | 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 2KB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC917FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 2K FLASH TSSOP16 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 2K FLASH, TSSOP16 |
| P89LPC917FDH,129 | 功能描述:8位微控制器 -MCU 80C51 2K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。