參數資料
型號： P87C591VFB
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 27 PF 5% 50V NPO/COG (0805) CHIP CAP TR
中文描述： 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP44
封裝： 10 X 10 X 1.75 MM, PLASTIC, QFP-44
文件頁數： 113/161頁
文件大小： 588K
代理商： P87C591VFB
1999 Aug 19
113
Philips Semiconductors
Objective Specification
Single-chip 8-bit microcontroller with CAN controller
P8xC591
16 TIMER 2
16.1
Features of Timer 2
Timer T2 is a 16-bit timer consisting of two registers TMH2
(HIGH byte) and TML2 (LOW byte). The 16-bit
timer/counter can be switched off or clocked via a
prescaler from one of two sources: f
CLK
/6 or an external
signal. When Timer T2 is configured as a counter, the
prescaler is clocked by an external signal on T2 (P3.O). A
rising edge on T2 increments the prescaler, and the
maximum repetition rate is one count per machine cycle
(1 MHz with a 6 MHz oscillator).
The maximum repetition rate for Timer T2 is twice the
maximum repetition rate for Timer 0 and Timer 1. T2 (P3.0)
is sampled at S2P1 and again at S5P1 (i.e., twice per
machine cycle). A rising edge is detected when T2 is LOW
during one sample and HIGH during the next sample. To
ensure that a rising edge is detected, the input signal must
be LOW for at least
1
2
cycle and then HIGH for at least
1
2
cycle. If a rising edge is detected before the end of S2P1,
the timer will be incremented during the following cycle;
otherwise it will be incremented one cycle later. The
prescaler has a programmable division factor of 1, 2, 4, or
8 and is cleared if its division factor or input source is
changed, or if the timer/counter is reset.
Timer T2 may be read “on the fly” but possesses no extra
read latches, and software precautions may have to be
taken to avoid misinterpretation in the event of an overflow
from least to most significant byte while Timer T2 is being
read. Timer T2 is not loadable and is reset by the RST
signal or by a rising edge on the input signal RT2, if
enabled. RT2 is enabled by setting bit T2ER (TM2CON.5).
When the least significant byte of the timer overflows or
when a 16-bit overflow occurs, an interrupt request may be
generated. Either or both of these overflows can be
programmed to request an interrupt. In both cases, the
interrupt vector will be the same. When the lower byte
(TML2) overflows, flag T2B0 (TM2CON) is set and flag
T20V (TM2lR) is set when TMH2 overflows. These flags
are set one cycle after an overflow occurs. Note that when
T20V is set, T2B0 will also be set. To enable the byte
overflow interrupt, bits ET2 (lEN1.7, enable overflow
interrupt, see Table 67) and T2lS0 (TM2CON.6, byte
overflow interrupt select) must be set. Bit TWBO
(TM2CON.4) is the Timer T2 byte overflow flag. To enable
the 16-bit overflow interrupt, bits ET2 (lE1.7, enable
overflow interrupt) and T2lS1 (TM2CON.7, 16-bit overflow
interrupt select) must be set. Bit T2OV (TM2lR.7) is the
Timer T2 16-bit overflow flag. All interrupt flags must be
reset by software. To enable both byte and 16-bit overflow,
T2lS0 and T2lS1 must be set and two interrupt service
routines are required. A test on the overflow flags indicates
which routine must be executed. For each routine, only the
corresponding overflow flag must be cleared. Timer T2
may be reset by a rising edge on RT2 (P3.1) if the Timer
T2 external reset enable bit (T2ER) in TM2CON is set.
This reset also clears the prescaler. In the Idle mode, the
timer/counter and prescaler are reset and halted. Timer T2
is controlled by the TM2CON special function register (see
Section 16.1.1).
Table 66
Timer T2 Interrupt Enable Register IEN1 (address E8H)
Table 67
Description of interrupt Enable Register IEN1 bits
7
6
5
4
3
2
1
0
ET2
ECAN
ECM1
ECM0
ECT3
ECT2
ECT1
ECT0
BIT
SYMBOL
FUNCTION
7
6
5
4
3
2
1
0
ET2
ECAN
ECM1
ECM0
ECT3
ECT2
ECT1
ECT0
Enable Timer T2 overflow interrupt(s).
Enable CAN interrupt.
Enable T2 Comparator 1 interrupt.
Enable T2 Comparator 0 interrupt.
Enable T2 Capture register 3 interrupt.
Enable T2 Capture register 2 interrupt.
Enable T2 Capture register 1 interrupt.
Enable T2 Capture register 0 interrupt.
相關PDF資料
PDF描述
P83C591SFA Single-chip 8-bit microcontroller with CAN controller
P87C591SFA Single-chip 8-bit microcontroller with CAN controller
P80C591SFB Single-chip 8-bit microcontroller with CAN controller
P83C591SFB Single-chip 8-bit microcontroller with CAN controller
P87C591SFB Single-chip 8-bit microcontroller with CAN controller
相關代理商/技術參數
參數描述
P87C654X2BBD,157 功能描述:8位微控制器 -MCU 16K/256 OTP 12/6 CLK I2C LQFP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87C654X2FA 制造商:NXP Semiconductors 功能描述:P87C654X2FA 8bit microcontroller,33MHz
P87C654X2FA,529 功能描述:8位微控制器 -MCU 16K/256 OTP 12/6 CLK RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87C654X2FA-S 功能描述:8位微控制器 -MCU 16K/256 OTP 12/6 CLK I2C PLCC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87C660X2BBD 功能描述:8位微控制器 -MCU 16K/512 OTP 12/6 CLK I2C PCA RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*