參數資料
型號： P83C524EFB
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： CONN 2O POS BOT ENTRY SFMT (BULK) 4-534991-2 TYCO, FCI BERG 69154-310
中文描述： 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
封裝： 10 X 10 X 1.75 MM, PLASTIC, QFP-44
文件頁數： 36/76頁
文件大?。?/td> 400K
代理商： P83C524EFB
1997 Dec 15
36
Philips Semiconductors
Product specification
8-bit microcontrollers
P83C524; P80C528; P83C528
Table 20
Description of the S1SCS bits
BIT
SYMBOL
FUNCTION
7
SDO/SDI
Serial Data Output and the filtered Serial Data Input
. SDI data is latched on the rising
edge of the filtered serial clock. S1SCS.7 accesses the same memory locations as
S1BIT.7. Access of the data bit via S1SCS will not start an auto-clock pulse.
Serial Clock Output and the filtered Serial Clock Input
. Serial clock output SCO is
'OR-ed' with the auto-clock. If SCO = 1 the auto-clock output is inhibited. The internal
clock stretching logic and external devices can pull the SCL line LOW. If the auto-clock
is not used, the SCL line has to be controlled by setting SCO = 1, waiting for CLH = 1
and setting SCO = 0 after the specified SCL HIGH time. (Because of the input filter,
CLH will be set at least 8 XTAL clock periods after the SCL LOW-to-HIGH transition.)
Serial Clock LOW-to-HIGH transition flag
: set with a rising edge of the filtered serial
clock. CLH = 1 indicates that, since the last CLH reset, a new valid data bit has been
latched in SDI. CLH can be reset by writing a 0 to S1SCS.5 or by a read/write of S1BIT.
Clearing CLH also clears RBF and WBF.
Bus Busy flag
: indicating that there has been a START condition that was not yet
followed by a STOP condition.
Read Bit Finished flag
: indicating a successful bit read.
RBF = 1 implies the following conditions:
CLH = 1: SCL had a rising edge
SCI = 0: the SCL pulse has finished
SI = 0: no START condition occurred
BB = 1: no STOP condition occurred
The RBF flag can be cleared by clearing the CLH flag.
Write Bit Finished flag
: indicating a successful bit write. The same conditions as for
RBF are true and also no 'arbitration loss' condition occurred. Arbitration is lost if a
1 data bit in SDO was over-ruled on SDA by an external device. The WBF flag can be
cleared by clearing the CLH flag.
STRetch control flag
. STR = 1 enables stretching of all SCL LOW periods. This allows
the processor in I
2
C slave mode to react on a fast master. The STR flag remains set
until cleared by writing a 0 to S1SCS.1.
6
SCO/SCI
5
CLH
4
BB
3
RBF
2
WBF
1
STR
The STretch (ST)
flag (not readable) pulls the serial clock LOW while ST = 1. The ST
flag is set on the falling edge of the filtered serial clock if STR = 1. It is also set after
reception of a START condition, regardless of the STR contents. ST is cleared with a
read or write of S1BIT.
ENable Serial I/O flag
. ENS = 1 enables the START detection and clock stretching
logic. ENS = 0 can be used to switch off the I
2
C-bus hardware. Note that the SDO and
SCO control flags must be set to 1 before ENS is set to avoid pulling SCL or SDA lines
to 0.
0
ENS
相關PDF資料
PDF描述
P83C524IFA 8-bit microcontrollers
P8748H HMOS SINGLE-COMPONENT 8-BIT MICROCONTROLLER
P8749H HMOS SINGLE-COMPONENT 8-BIT MICROCONTROLLER
P8751BH MCS51 8-BIT CONTROL-ORIENTED MICROCONTROLLERS
P8751H MCS51 8-BIT CONTROL-ORIENTED MICROCONTROLLERS
相關代理商/技術參數
參數描述
P83C524EFP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers
P83C524FFA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P83C524FFP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P83C524FHA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P83C524FHP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*