- 您現在的位置：買賣IC網 > PDF目錄367723 > P80C591 (NXP Semiconductors N.V.) Single-chip 8-bit microcontroller with CAN controller PDF資料下載
參數資料
| 型號： | P80C591 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Single-chip 8-bit microcontroller with CAN controller |
| 中文描述： | 單芯片8 - CAN控制器位微控制器 |
| 文件頁數： | 80/161頁 |
| 文件大?。?/td> | 588K |
| 代理商： | P80C591 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
1999 Aug 19
80
Philips Semiconductors
Objective Specification
Single-chip 8-bit microcontroller with CAN controller
P8xC591
Fig.34 Serial Clock Synchronization.
handbook, full pagewidth
MHI035
SDA
SCL
(1)
(3)
(1)
(2)
mark
duration
space duration
(1) Another service pulls the SCL line low before the SIO “mask” duration is complete. The serial clock generator
is immediately reset and commences with the “space” duration by pulling SCL low.
(2) Another device still pulls the SCL line low after SIO1 releases SCL. The serial clock generator is forced into
the wait state until the SCL line is released.
(3) The SCL line is released, and the serial clock generator commences with the mark duration.
15.2.6
S
ERIAL
C
LOCK
G
ENERATOR
This programmable clock pulse generator provides the
SCL clock pulses when SIO1 is in the master transmitter
or master receiver mode. It is switched off when SIO1 is in
a slave mode. The programmable output clock
frequencies are: f
CLK
/120, f
CLK
/9600, and the Timer 1
overflow rate divided by eight. The output clock pulses
have a 50% duty cycle unless the clock generator is
synchronized with other SCL clock sources as described
above.
15.2.7
T
IMING AND
C
ONTROL
The timing and control logic generates the timing and
control signals for serial byte handling. This logic block
provides the shift pulses for S1DAT, enables the
comparator, generates and detects start and stop
conditions, receives and transmits acknowledge bits,
controls the master and slave modes, contains interrupt
request logic, and monitors the I
2
C bus status.
15.2.8
C
ONTROL
R
EGISTER
, S1CON
This 7-bit special function register is used by the
microcontroller to control the following SIO1 functions:
start and restart of a serial transfer, termination of a serial
transfer, bit rate, address recognition, and
acknowledgment.
15.2.9
S
TATUS
D
ECODER AND
S
TATUS
R
EGISTER
The status decoder takes all of the internal status bits and
compresses them into a 5-bit code. This code is unique for
each I
2
C bus status. The 5-bit code may be used to
generate vector addresses for fast processing of the
various service routines. Each service routine processes a
particular bus status. There are 26 possible bus states if all
four modes of SIO1 are used. The 5-bit status code is
latched into the five most significant bits of the status
register when the serial interrupt flag is set (by hardware)
and remains stable until the interrupt flag is cleared by
software. The three least significant bits of the status
register are always zero. If the status code is used as a
vector to service routines, then the routines are displaced
by eight address locations. Eight bytes of code is sufficient
for most of the service routines (see the software example
in this section).
15.2.10 T
HE
F
OUR
SIO1 S
PECIAL
F
UNCTION
R
EGISTERS
The microcontroller interfaces to SIO1 via four special
function registers. These four SFRs (S1ADR, S1DAT,
S1CON, and S1STA) are described individually in the
following sections.
相關PDF資料 |
PDF描述 |
|---|---|
| P83C591 | Single-chip 8-bit microcontroller with CAN controller |
| P87C591 | Single-chip 8-bit microcontroller with CAN controller |
| P83C591VFA | Single-chip 8-bit microcontroller with CAN controller |
| P80CE560 | 8-BIT SINGLE CHIP MICROCONTROLLERS |
| P87CE560EFB | BATTERY CHG UNIV 12VDC @ 500MA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P80C591SFA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller |
| P80C591SFB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller |
| P80C592 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P80C592FFA | 制造商:NXP Semiconductors 功能描述: |
| P80C592FFA/00,512 | 功能描述:8位微控制器 -MCU 80C51 W/CAN 16MHZ ROMLESS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。