- 您現在的位置：買賣IC網 > PDF目錄367741 > P80C557E6 (NXP Semiconductors N.V.) Single-chip 8-bit microcontroller(單片8位微控制器) PDF資料下載
參數資料
| 型號： | P80C557E6 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Single-chip 8-bit microcontroller(單片8位微控制器) |
| 中文描述： | 單芯片8位微控制器（單片8位微控制器） |
| 文件頁數： | 44/64頁 |
| 文件大?。?/td> | 476K |
| 代理商： | P80C557E6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Philips Semiconductors
Product specification
P83C557E6/P80C557E6
Single-chip 8-bit microcontroller
1999 Mar 02
44
6.13.4
This counter provides an overflow signal every second, when the
32kHz oscillator is running.
Seconds Timer
The overflow output sets the interrupt flag SECINT. This interrupt
can be disabled/enabled by ENSECI. If SECINT is enabled, it is
logically ORed with INT1 (external interrupt 1).
Seconds interrupt and INT1 therefor share the same priority and
vector. The software has to check both flags SECINT (PLLCON.5)
and IE1 (TCON.3), to distinguish between the two interrupt sources.
SECINT can only be cleared via writing a ‘0’ to this bit .
The external interrupts INT0 , INT1 or the seconds interrupt can
Wake–up the PLL oscillator and the microcontroller as described in
chapter “Wake–up from Power–down Mode”.
For a Wake–up via INT1 or seconds interrupt, IE1 must be enabled
and level–sensitive.
A further function of the seconds timer is to control the start–up
timing of the microcontroller after Reset or after Wake–up from
Power–down. It controls the stretching of the reset pulse to the
microcontroller and controls releasing the system clock to the
microcontroller.
A RSTIN signal of 1us at minimum will reset the microcontroller.
In case of Reset or Wake–up with halted 32kHz oscillator: From
RSTIN falling edge or Wake–up interrupt it takes 560ms at
maximum for the start–up of the 32kHz oscillator itself and the
stabilization of the PLL’s.
In case of Wake–up with running 32kHz oscillator: From Wake–up
interrupt it takes about 1ms for the stabilization of the PLL’s.
After this start–up time, the microcontroller is supplied with the
system clock and – in case of a reset – the internally
stretched reset
signal overlaps about 45us, to guarantee a proper initialization of the
microcontroller.
For further information refer to section 6.11 Power reduction modes.
XTAL3
Figure 45. Block diagram PLL
Oscil–
lator
32.768 KHz
C
1
32 kHz
Phase
comparator
Loop
filter
CCO
PD
Internal Bus
SECONDS TIMER
PLLCON
RSTIN
Programmable
divider
system clock
Reset to controller
’Seconds’
Interrupt
request
PD = power down
Stretched
Reset
RUN32 PD
R
f
C
2
XTAL4
相關PDF資料 |
PDF描述 |
|---|---|
| P89C58 | 80C51 8-bit microcontroller family 4K/8K/16K/32K Flash |
| P89C54X2 | 80C51 8-bit Flash microcontroller family |
| P89C54X2BA | 80C51 8-bit Flash microcontroller family |
| P89C54X2BBD | 80C51 8-bit Flash microcontroller family |
| P89C54X2BN | 80C51 8-bit Flash microcontroller family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P80C557E6EBB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P80C557E6EFB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P80C557E8 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8 BIT MICROCONTROLLER |
| P80C557E8EFB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| P80C562 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller |
發布緊急采購，3分鐘左右您將得到回復。