參數資料
型號： ORSO82G5-2FN680C
廠商： Lattice Semiconductor Corporation
文件頁數： 18/153頁
文件大?。?/td> 0K
描述： IC TRANCEIVERS FPSC 680FPBGA
產品變化通告： Product Discontinuation 01/Aug/2011
標準包裝： 24
系列： *
Lattice Semiconductor
ORCA ORSO42G5 and ORSO82G5 Data Sheet
114
P[TBLR]CLK[1:0][TC]
I
Pins dedicated for the primary clock. Input pins on the middle of each side with differential pair-
ing.
I/O After conguration these pins are user programmable I/O, if not used for clock inputs.
TDI, TCK, TMS
I
If boundary-scan is used, these pins are test data in, test clock, and test mode select inputs. If
boundary-scan is not selected, all boundary-scan functions are inhibited once conguration is
complete. Even if boundary-scan is not used, either TCK or TMS must be held at logic 1 during
conguration. Each pin has a pull-up enabled during conguration.
I/O After conguration, these pins are user-programmable I/O if boundary scan is not used.
1
RDY/BUSY/RCLK
O
During conguration in asynchronous peripheral mode, RDY/RCLK indicates another byte can
be written to the FPGA. If a read operation is done when the device is selected, the same sta-
tus is also available on D7 in asynchronous peripheral mode.
During the master parallel conguration mode, RCLK is a read output signal to an external
memory. This output is not normally used.
I/O After conguration this pin is a user-programmable I/O pin.
1
HDC
O
High During Conguration is output high until conguration is complete. It is used as a control
output, indicating that conguration is not complete.
I/O After conguration, this pin is a user-programmable I/O pin.
1
LDC
O
Low During Conguration
is output low until conguration is complete. It is used as a control out-
put, indicating that conguration is not complete.
I/O After conguration, this pin is a user-programmable I/O pin.
1
INIT
I/O INIT is a bidirectional signal before and during conguration. During conguration, a pull-up is
enabled, but an external pull-up resistor is recommended. As an active-low open-drain output,
INIT
is held low during power stabilization and internal clearing of memory. As an active-low
input, INIT holds the FPGA in the wait-state before the start of conguration.
After conguration, this pin is a user-programmable I/O pin.
1
CS0, CS1
I
CS0
and CS1 are used in the asynchronous peripheral, slave parallel, and microprocessor con-
guration modes. The FPGA is selected when CS0 is low and CS1 is high. During congura-
tion, a pull-up is enabled.
I/O After conguration, if MPI is not used, these pins are user-programmable I/O pins.
1
RD/MPI_STRB
I
RD
is used in the asynchronous peripheral conguration mode. A low on RD changes D[7:3]
into a status output. WR and RD should not be used simultaneously. If they are, the write strobe
overrides.
This pin is also used as the
MPI data transfer strobe. As a status indication, a high indicates
ready, and a low indicates busy.
WR/MPI_RW
I
WR is used in asynchronous peripheral mode. A low on WR transfers data on D[7:0] to the
FPGA.
In MPI mode, a high on MPI_RW allows a read from the data bus, while a low causes a write
transfer to the FPGA.
I/O After conguration, if the MPI is not used, WR/MPI_RW is a user-programmable I/O pin.
1
PPC_A[14:31]
I
During MPI mode the PPC_A[14:31] are used as the address bus driven by the PowerPC bus
master utilizing the least-signicant bits of the PowerPC 32-bit address.
MPI_BURST
I
MPI_BURST is driven low to indicate a burst transfer is in progress in MPI mode. Driven high
indicates that the current transfer is not a burst.
MPI_BDIP
I
MPI_BDIP is driven by the PowerPC processor in MPI mode. Assertion of this pin indicates that
the second beat in front of the current one is requested by the master. Negated before the burst
transfer ends to abort the burst data phase.
MPI_TSZ[0:1]
I
MPI_TSZ[0:1] signals are driven by the bus master in MPI mode to indicate the data transfer
size for the transaction. Set 01 for byte, 10 for half-word, and 00 for word.
A[21:0]
O
During master parallel mode A[21:0] address the conguration EPROMs up to 4M bytes.
I/O If not used for MPI these pins are user-programmable I/O pins after conguration.
1
Table 47. Pin Descriptions (Continued)
Symbol
I/O
Description
相關PDF資料
PDF描述
TPS2371PWR IC PWR INTRFCE SW FOR POE 8TSSOP
PIC32MX575F512H-80V/PT IC MCU 32BIT 512KB FLASH 64TQFP
PIC32MX775F256H-80V/PT IC MCU 32BIT 256KB FLASH 64TQFP
VI-J4D-IW-F1 CONVERTER MOD DC/DC 85V 100W
PIC24EP512GP806-I/MR IC MCU 8BIT 512KB FLASH 64-QFN
相關代理商/技術參數
參數描述
ORSO82G5-2FN680C1 功能描述:FPGA - 現場可編程門陣列 10368 LUT 372 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORSO82G5-2FN680I 功能描述:FPGA - 現場可編程門陣列 ORCA FPSC 2.7 Gb Bp ln Xcvr 643K Gt I RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORSO82G5-2FN680I1 功能描述:FPGA - 現場可編程門陣列 10368 LUT 372 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORSO82G5-3BM680C 功能描述:FPGA - 現場可編程門陣列 10368 LUT 372 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORSO82G5-3F680C 功能描述:FPGA - 現場可編程門陣列 ORCA FPSC 2.7GBITS/s BP XCVR 643K RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*