- 您現在的位置：買賣IC網 > PDF目錄363670 > NT7502H-TABF1 (Electronic Theatre Controls, Inc.) 65 X 132 RAM-Map LCD Controller / Driver PDF資料下載
參數資料
| 型號： | NT7502H-TABF1 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 65 X 132 RAM-Map LCD Controller / Driver |
| 中文描述： | 65 × 132 RAM的地圖LCD控制器/驅動器 |
| 文件頁數： | 29/54頁 |
| 文件大小： | 687K |
| 代理商： | NT7502H-TABF1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
NT7502
19. Static Indicator (Double Byte Command)
This command controls the static drive system indicator display. The static indicator display is controlled by this command
only, and is independent of other display control commands.
This is used when one of the static indicator liquid crystal drive electrodes is connected to the FR terminal, and the other is
connected to the FRS terminal. A different pattern is recommended for the static indicator electrodes rather than for the
dynamic drive electrodes. If the pattern is too close, it can result in deterioration of the liquid crystal and of the electrodes.
The static indicator ON command is a double-byte command paired with the static indicator register set command, and thus
command must be executed one after the other. (The static indicator OFF command is a single byte command.)
!
Static Indicator ON/OFF
When the static indicator ON command is entered, the static indicator register set command is enabled. Once the static
indicator ON command has been entered, no other command aside from the static indicator register set command can be
used. This mode is cleared when data is set in the register by the static indicator register set command.
A0
E
RD
W
R
/
WR
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
1
0
1
0
1
1
0
D
D = 0: Static Indicator OFF
D = 1: Static Indicator ON
!
Static Indicator Register Set
This command sets two bits of data into the static indicator register and is used to set the static indicator into a blinking
mode.
A0
E
RD
1
W
R
/
WR
0
D7 D6 D5 D4 D3 D2
D1
D0
Indicator Display State
0
*
*
*
*
*
*
0
0
1
1
0
1
0
1
OFF
ON (blinking at approximately 0.5 second intervals
ON (blinking at approximately 1 second intervals
ON (constantly on)
* Disabled bit
20. Power Save (Compound Command)
When all displays are turned on during display off, the Power Save command is issued to greatly reduce current
consumption.
If the static indicators are off, the Power Save command drives the system into sleep mode. If on, this command drives the
system into standby mode.
Release the Sleep mode using both the Power Save OFF command (Display ON command or Entire Display OFF
command) and Set Indicator On command.
Static Indicator OFF
Static Indicator ON
Power Save
(Display OFF and Entire Display ON)
(Sleep mode)
(Standby mode)
Power Save OFF
(Display ON or Entire Displays OFF )
Static Indicator ON
(Sleep mode released)
(Standby mode released)
29
相關PDF資料 |
PDF描述 |
|---|---|
| NT7603 | 2 x 110 W class-D power amplifer, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7603BDB-01 | Class D Audio Amplifier, SOT549-1 (HTSSOP32), Reel Dry Pack, SMD, 13" |
| NT7603BDT-01 | 2 x 150 W class-D power amplifier, SOT411-1 (DBS23P), Tube |
| NT7603BDW-01 | 2 x 150 W class-D power amplifier, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7701 | 160 Output LCD Segment/Common Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT75-1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT751AS12DC110V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
| NT751AS12DC12V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
| NT75-1AS12DC12V0.253.5 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT75-1AS12DC12V0.255.0 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
發布緊急采購，3分鐘左右您將得到回復。