- 您現在的位置：買賣IC網 > PDF目錄363670 > NT7502H-TABF1 (Electronic Theatre Controls, Inc.) 65 X 132 RAM-Map LCD Controller / Driver PDF資料下載
參數資料
| 型號： | NT7502H-TABF1 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 65 X 132 RAM-Map LCD Controller / Driver |
| 中文描述： | 65 × 132 RAM的地圖LCD控制器/驅動器 |
| 文件頁數： | 22/54頁 |
| 文件大小： | 687K |
| 代理商： | NT7502H-TABF1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
NT7502
Reset Circuit
When the RES input falls to “L”, these LSI reenter their default state. The default settings are shown below:
1. Display OFF
2. Normal display
3. ADC select: Normal display (ADC command D0 = “L”)
4. Power control register (D2, D1, D0) = (0, 0, 0,)
5. Register data clear in serial interface
6. LCD power supply bias ratio 1/9 (1/65 duty), 1/8 (1/55, 1/49 duty), 1/6 (1/33 duty)
7. Read modify write OFF
8. Static indicator: OFF
Static indicator register: (D1, D2) = (0, 0)
9. Display start line register set at first line
10. Column address counter set at address0
11. Page address register set at page 0
12. Common output status normal
13. V0 voltage regulator internal power supply ratio set mode clear:
V0 voltage regulator internal resistor ratio register: (D2, D1, D0) = (1, 0, 0)
14. Electronic volume register set mode clear
Electronic volume register: (D5, D4, D3, D2, D1, D0) = (1, 0, 0, 0, 0, 0,)
15. Test mode clear
16. All-indicator-lamps-on OFF (All-indicator-lamps ON/OFF command D0 = “L”)
17. Output condition of COM, SEG
COM:
V1
SEG:
V2
On the other hand, when the reset command is used, only default settings 7 to 15 above are put into effect.
The MPU interface (Reference Example)”, the RES terminal is connected to the MPU reset terminal, making the chip
reinitialize simultaneously with the MPU. At the time of power up, it is necessary to reinitialize using the RES terminal.
Moreover, when the control signal from the MPU is in a high impedance state, there may be an overcurrent condition; therefore,
take measures to prevent the input terminal from entering a high impedance state.
In the NT7502, if the internal liquid crystal power supply circuit is not used, then it is necessary to apply a “L” signal to the RES
terminal when the external liquid crystal power supply is applied.
Even though the oscillator circuit operates while the RES terminal is “L,” the display timing generator circuit is stopped, and the
FR, FRS, and DOF terminals are fixed to “H,” and the CL pin is fixed to “H” only when the intermal oscillator circuit is used.
There is no influence on the D0 to D7 terminals.
22
相關PDF資料 |
PDF描述 |
|---|---|
| NT7603 | 2 x 110 W class-D power amplifer, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7603BDB-01 | Class D Audio Amplifier, SOT549-1 (HTSSOP32), Reel Dry Pack, SMD, 13" |
| NT7603BDT-01 | 2 x 150 W class-D power amplifier, SOT411-1 (DBS23P), Tube |
| NT7603BDW-01 | 2 x 150 W class-D power amplifier, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7701 | 160 Output LCD Segment/Common Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT75-1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT751AS12DC110V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
| NT751AS12DC12V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
| NT75-1AS12DC12V0.253.5 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT75-1AS12DC12V0.255.0 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
發布緊急采購，3分鐘左右您將得到回復。