- 您現在的位置：買賣IC網 > PDF目錄98048 > MTSF3N02HDR2 (ON SEMICONDUCTOR) 4000 mA, 20 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET PDF資料下載
參數資料
| 型號： | MTSF3N02HDR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 小信號晶體管 |
| 英文描述： | 4000 mA, 20 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| 封裝： | MICROPAK-8 |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 137K |
| 代理商： | MTSF3N02HDR2 |
MTSF3N02HD
http://onsemi.com
10
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 14 shows a typical heating
profile for use when soldering a surface mount device to a
printed circuit board. This profile will vary among
soldering systems, but it is a good starting point. Factors
that can affect the profile include the type of soldering
system in use, density and types of components on the
board, type of solder used, and the type of board or
substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density
board. The Vitronics SMD310 convection/infrared reflow
soldering system was used to generate this profile. The type
of solder used was 62/36/2 Tin Lead Silver with a melting
point between 177–189
°C. When this type of furnace is
used for solder reflow work, the circuit boards and solder
joints tend to heat first. The components on the board are
then heated by conduction. The circuit board, because it has
a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may
be up to 30 degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°C
150
°C
100
°C
5
°C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
° TO 219°C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°C
150
°C
160
°C
170
°C
140
°C
Figure 17. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| MTSF3N03HDR2 | 3800 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MTSF3N03HDR2 | 3700 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MU9C8148FC | SPECIALTY MICROPROCESSOR CIRCUIT, PQCC68 |
| MUN2115T3 | 100 mA, 50 V, PNP, Si, SMALL SIGNAL TRANSISTOR |
| MUN2133T3 | 100 mA, 50 V, PNP, Si, SMALL SIGNAL TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTSF3N03HD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:SINGLE TMOS POWER MOSFET 3.8 AMPERES 30 VOLTS RDS(on) = 0.040 OHM |
| MTSF3N03HDR2 | 制造商:ON Semiconductor 功能描述:Trans MOSFET N-CH 30V 5.7A 8-Pin SOP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MTSF3N03HDR2G | 功能描述:MOSFET NFET 30V 3A 40MO RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MTSFAF500FMEF-001 | 功能描述:ACCY MOUNT SURF NMO 5M FMEF RoHS:是 類別:RF/IF 和 RFID >> RF配件 系列:* 標準包裝:1 系列:* |
| MTSG206PA | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。