參數資料
型號： MT8930CP
廠商： ZARLINK SEMICONDUCTOR INC
元件分類： 數字傳輸電路
英文描述： Subscriber Network Interface Circuit
中文描述： DATACOM, DIGITAL SLIC, PQCC44
封裝： PLASTIC, MS-018AC, LCC-44
文件頁數： 3/41頁
文件大?。?/td> 2516K
代理商： MT8930CP
Data Sheet
MT8930C
3
9
16
R/W
/
WR
AFT/PRI
Read/Write or Write Input (Cmode = 1):
defines the data bus transfer as a read (R/
W=1) or a write (R/W=0) in Motorola bus mode. Redefined to WR in Intel bus mode.
Adaptive-Fixed Timing/Priority Select Input (Cmode=0)
: in NT mode, causes the
PLL and Rx filters and peak detectors to be disabled in favour of fixed timing and fixed
thresholds for short passive bus operation (0=fixed, 1=adaptive). In TE mode, this is the
Priority input. High priority (PRI=1) is normally reserved for signalling.
10
17
DS/RD
DinB
Data Strobe/Read Input (Cmode = 1):
active high input indicates to the SNIC that
valid data is on the bus during a write operation or that the SNIC must output data
during a read operation in Motorola bus mode. Redefined to RD in Intel bus mode.
D-Channel in B1 Timeslot Input (Cmode = 0):
active high input that causes all
eight ST-BUS D-channel bits, instead of the usual two bits, to be routed to and
from the S-interface B1 timeslot. When active, marks are transmitted in the
S-interface D-channel.
Address Strobe/Address Latch Enable Input (Cmode = 1):
in Motorola bus mode
the falling edge is used to strobe the address into the SNIC during microprocessor
access. Redefined to ALE in Intel bus mode.
Parallel/Serial Control Input (Cmode = 0):
determines if the serial C-channel
(
P
/
SC=0) or microport pins (P/SC=1) are the source of chip control when controllerless
mode is selected. If the ST-BUS is chosen as the source, the dedicated Control input
pins are ignored but the status output pins remain valid.
11
19
AS/ALE
P/SC
12
20
CS
DReq
IC
Chip Select Input (Cmode=1):
active low input used to select the SNIC for
microprocessor access
.
D-Channel Request Input (Cmode = 0):
an active high input that in TE mode only
causes the SNIC to transmit a “01111110” flag immediately if the D-channel is free, or
wait until it becomes available and then transmit the flag. The DCack signals the
successful acquisition of the D-channel. If DReq is tied low, continuous ones are
transmitted in the S-Bus D-channel.
Internal Connection (Cmode = 0):
tie to V
SS
for normal operation in NT mode only.
Interrupt Request (Open Drain Output) (Cmode = 1):
an output indicating an
unmasked HDLC interrupt. The interrupt remains active until the microprocessor clears
it by reading the HDLC Interrupt Status Register. This interrupt source is enabled with
B2=0 of Master Control Register.
New Data Available (Open Drain Output) (Cmode = 1):
an active low output signal
indicating availability of new data from the S-Bus. This signal is selected with B2=1 of
Master Control Register.
D-Channel Acknowledge (Open Drain Output) (Cmode = 0):
in TE mode only
indicates that the SNIC has gained access to the D-channel in response to a DReq and
has transmitted the first zero of an opening flag. The user should immediately begin
transmitting the rest of the packet over the ST-BUS D-channel. If this signal goes high
in the middle of transmission, the TE has lost the bus and must regain access of the D-
channel before retransmitting the packet.
Internal Connection (Open Drain Output) (C-mode=0).
This pin is not used in NT
mode and should be left disconnected.
This pin must be tied to V
DD
with a 10k
resistor.
Ground.
Bidirectional Address/Data Bus (Cmode = 1):
electrically and logically compatible to
either Intel or Motorola micro-bus specifications. If DS/RD is low on the rising edge of
AS/ALE then the chip operates to Motorola specs. If DS/RD is high on the rising edge
of AS/ALE Intel mode is selected. Taking Rsti low sets Motorola mode.
Internal State Outputs (Cmode =0):
Binary encoded state number outputs.
IS0
IS1
NT Mode
0
0
deactivated
0
1
pending deactivation
1
0
pending activation
1
1
activated
13
21
IRQ
NDA
DCack
IC
14
15-
22
22
V
SS
AD0-7
24-26
30-32
34-35
15-
16
24-
25
IS0-IS1
TE Mode
deactivated
synchronized
activation request
activated
Pin Description (continued)
Pin #
Name
Description
DIP
PLCC
相關PDF資料
PDF描述
MT8931C Subscriber Network Interface Circuit
MT8931CE Subscriber Network Interface Circuit
MT8931CP Subscriber Network Interface Circuit
MT8931C-1 CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit
MT8931CE CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information
相關代理商/技術參數
參數描述
MT8930CPR 制造商:Microsemi Corporation 功能描述:
MT8931B 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
MT8931BC 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
MT8931BE 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
MT8931BP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*