參數資料
型號： MT8930CP
廠商： ZARLINK SEMICONDUCTOR INC
元件分類： 數字傳輸電路
英文描述： Subscriber Network Interface Circuit
中文描述： DATACOM, DIGITAL SLIC, PQCC44
封裝： PLASTIC, MS-018AC, LCC-44
文件頁數： 24/41頁
文件大?。?/td> 2516K
代理商： MT8930CP
MT8930C
Data Sheet
24
Table 16. TE Mode C-channel Control Register
(2)
(Write Add. 01000
B
and B0 = 0)
Note 1:
Note 2:
Allow one ST-BUS frame to input the C-channel and one ST-BUS frame to establish the connection.
The C-channel Control Register is updated once every ST-BUS frame. Therefore, this register should not be written to
more than once per frame, otherwise, the last access will override previous ones.
Table 17. TE Mode Diagnostic Register (Write Add. 01000
B
and B0 = 1)
BIT
NAME
DESCRIPTION
B7
AR
Setting this bit will initiate the activation of the S-Bus.
If ’0’, the device will remain in the present state.
B6
DR
Setting this bit will initiate the deactivation of the S-Bus.
If ’0’, the device will remain in the present state. This bit has priority over AR.
B5
DinB
If ’1’, the D-channel will be placed in the B1 timeslot allocating 64 kbit/s to the
D-channel.
(1)
If ’0’, the D-channel will assume its position with a 16 kbit/s bandwidth.
(1)
B4
Priority
The status of this bit selects the priority class of the terminal equipment. A ’1’ selects the
high priority and a ’0’ selects the low priority.
B3
DReq
This bit is used to request or relinquish the D-channel on the S-Bus when the D-channel
source is the ST-BUS. A ’1’ will request the D-channel, a ’0’ will relinquish it.
Keep at ’0’ when the D-channel source is the HDLC transmitter.
B2
TxMCH
The state of this bit will be transmitted in the maintenance channel (Q-channel).
B1
ClrDia
A ’1’ will clear the contents of the Diagnostics Register.
A ’0’ will enable the maintenance functions found in the Diagnostic Register.
This bit should be set to 1 as long as the device is not fully active (IS0, IS1
≠
1,1).
B0
RegSel
If the register select bit is set to ’1’, the control register is redefined as the diagnostic
Register. A ’0’ gives access to the Control Register.
BIT
NAME
DESCRIPTION
B7-B6
Loop
The status of these two bits determine which type of loopback is to be performed:
B7 - B6
0 - 0
- no loopback active
0 - 1
- near end loopback LTx to LRx
1 - 0
- digital loopback DSTi to DSTo
1 - 1
- remote loopback LRx to LTx
B5
FSync
If ’1’, the device will maintain frame synchronization even after losing the frame sync
sequence (i.e., if the device is transmitting INFO3 and this bit is set, INFO3 will still be
transmitted even if the frame sync sequence in the received signal is lost).
If ’0’, synchronization will be declared when three consecutive framing sequences have
been detected.
B4
FLv
If ’1’, the frame sync sequence will violate the normal bipolar encoding rule.
If ’0’, the framing pattern resumes normal operation, i.e., framing bit will be a bipolar
violation.
B3
Idle
If ’1’, an all 1s signal is transmitted on the line.
If ’0’, the transmitter will resume normal operation.
B2-B1
NA
Unused.
B0
RegSel
If the register select bit is set to ’1’, the control register is redefined as the diagnostic
register. A ’0’ gives access to the control register.
相關PDF資料
PDF描述
MT8931C Subscriber Network Interface Circuit
MT8931CE Subscriber Network Interface Circuit
MT8931CP Subscriber Network Interface Circuit
MT8931C-1 CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit
MT8931CE CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information
相關代理商/技術參數
參數描述
MT8930CPR 制造商:Microsemi Corporation 功能描述:
MT8931B 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
MT8931BC 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
MT8931BE 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
MT8931BP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*