- 您現在的位置：買賣IC網 > PDF目錄45322 > MT80C51T-36D (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MT80C51T-36D |
| 廠商： | TEMIC SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44 |
| 文件頁數： | 170/189頁 |
| 文件大?。?/td> | 4133K |
| 代理商： | MT80C51T-36D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁當前第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
99
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
The collision detection is enabled in transmit mode, when the output driver has been disabled. The data line should
now be kept high by the internal pull-up and it is monitored to see, if it is driven low by the external programmer. If
the output is read low, a collision has been detected.
There are some potential pit-falls related to the way collision detection is performed. For example, collisions cannot
be detected when the TPI physical layer transmits a bit-stream of successive logical zeros, or bit-stream of alter-
nating logical ones and zeros. This is because the output driver is active all the time, preventing polling of the
TPIDATA line. However, within a single frame the two stop bits should always be transmitted as logical ones,
enabling collision detection at least once per frame (as long as the frame format is not violated regarding the stop
bits).
The TPI physical layer will cease transmission when it detects a collision on the TPIDATA line. The collision is sig-
nalized to the TPI access layer, which immediately changes the physical layer to receive mode and goes to the
error state. The TPI access layer can be recovered from the error state only by sending a BREAK character.
14.3.10
Direction Change
In order to ensure correct timing of the half-duplex operation, a simple guard time mechanism has been added to
the physical layer. When the TPI physical layer changes from receive to transmit mode, a configurable number of
additional IDLE bits are inserted before the start bit is transmitted. The minimum transition time between receive
and transmit mode is two IDLE bits. The total IDLE time is the specified guard time plus two IDLE bits.
The guard time is configured by dedicated bits in the TPIPCR register. The default guard time value after the phys-
ical layer is initialized is 128 bits.
The external programmer looses control of the TPIDATA line when the TPI target changes from receive mode to
transmit. The guard time feature relaxes this critical phase of the communication. When the external programmer
changes from receive mode to transmit, a minimum of one IDLE bit should be inserted before the start bit is
transmitted.
14.4
Access Layer of Tiny Programming Interface
The TPI access layer is responsible for handling the communication with the external programmer. The communi-
cation is based on message format, where each message comprises an instruction followed by one or more byte-
sized operands. The instruction is always sent by the external programmer but operands are sent either by the
external programmer or by the TPI access layer, depending on the type of instruction issued.
The TPI access layer controls the character transfer direction on the TPI physical layer. It also handles the recov-
ery from the error state after exception.
The Control and Status Space (CSS) of the Tiny Programming Interface is allocated for control and status registers
in the TPI access Layer. The CSS consist of registers directly involved in the operation of the TPI itself. These reg-
ister are accessible using the SLDCS and SSTCS instructions.
The access layer can also access the data space, either directly or indirectly using the Pointer Register (PR) as the
address pointer. The data space is accessible using the SLD, SST, SIN and SOUT instructions. The address
pointer can be stored in the Pointer Register using the SLDPR instruction.
14.4.1
Message format
Each message comprises an instruction followed by one or more byte operands. The instruction is always sent by
the external programmer. Depending on the instruction all the following operands are sent either by the external
programmer or by the TPI.
The messages can be categorized in two types based on the instruction, as follows:
Write messages. A write message is a request to write data. The write message is sent entirely by the external
programmer. This message type is used with the SSTCS, SST, STPR, SOUT and SKEY instructions.
相關PDF資料 |
PDF描述 |
|---|---|
| MS80C31-12R | 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44 |
| MT80C51C-12D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44 |
| MS80C31-20R | 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44 |
| MV80C51T-16D | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| MP80C31-30D | 8-BIT, 30 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT80GB | 制造商:Datak Corporation 功能描述: |
| MT80JSF1G72NDY-1G1F1A2 | 制造商:Micron Technology Inc 功能描述:8GB 1GX72 DDR3 SDRAM MODULE PBF DIMM 1.5V REGISTERED - Trays |
| MT80KSF1G72NDY-1G4F1A3 | 制造商:Micron Technology Inc 功能描述:8GB 1GX72 DDR3 SDRAM MODULE PBF DIMM 1.35V FULLY BUFFERED - Trays |
| MT810 | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:STANDARD T-1 3/4 LED LAMPS |
| MT-8100 | 制造商:Eclipse Tools 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。