- 您現在的位置：買賣IC網 > PDF目錄384756 > MT49H16M18C (Micron Technology, Inc.) 288Mb SIO REDUCED LATENCY(RLDRAM II) PDF資料下載
參數資料
| 型號： | MT49H16M18C |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | 288Mb SIO REDUCED LATENCY(RLDRAM II) |
| 中文描述： | 288Mb二氧化硅約化延遲（延遲DRAM二） |
| 文件頁數： | 11/44頁 |
| 文件大?。?/td> | 1117K |
| 代理商： | MT49H16M18C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
16 MEG x 18, 32 MEG x 9
2.5V V
EXT
, 1.8V V
DD
, HSTL, SIO, RLDRAM II
pdf: 09005aef80a41b59/zip: 09005aef811ba111
MT49H8M18C_2.fm - Rev. F 11/04 EN
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2004 Micron Technology, Inc. All rights reserved.
11
NOTE:
1. When the chip is deselected, internal NOP commands are generated and no commands are accepted.
2. Actual refresh is 32ms/8K/8 = 0.488μs.
3. Actual refresh is 32ms/8k = 3.90μs.
Table 5:
Description of Commands
COMMAND
DESCRIPTION
DESEL/NOP
1
The NOP command is used to perform a no operation to the RLDRAM, which essentially deselects
the chip. Use the NOP command to prevent unwanted commands from being registered during
idle or wait states. Operations already in progress are not affected. Output values depend on
command history.
The mode register is set via the address inputs A(17:0). See Figure 10 on page 16 for further
information. The MRS command can only be issued when all banks are idle and no bursts are in
progress.
The READ command is used to initiate a burst read access to a bank. The value on the BA(2:0)
inputs selects the bank, and the address provided on inputs A(20:0) selects the data location within
the bank.
The WRITE command is used to initiate a burst write access to a bank. The value on the BA(2:0)
inputs selects the bank, and the address provided on inputs A(20:0) selects the data location within
the bank. Input data appearing on the DS is written to the memory array subject to the DM input
logic level appearing coincident with the data. If the DM signal is registered LOW, the
corresponding data will be written to memory. If the DM signal is registered HIGH, the
corresponding data inputs will be ignored (i.e., this part of the data word will not be written).
The AREF is used during normal operation of the RLDRAM to refresh the memory content of a
bank. The command is nonpersistent, so it must be issued each time a refresh is required. The value
on the BA(2:0) inputs selects the bank. The refresh address is generated by an internal refresh
controller, effectively making each address bit a “Don’t Care” during the AREF command. The
RLDRAM requires 64K cycles at an average periodic interval of 0.49μs
2
(MAX). To improve
efficiency, eight AREF commands (one for each bank) can be posted to the RLDRAM at periodic
intervals of 3.9μs
3
.
MRS
READ
WRITE
AREF
相關PDF資料 |
PDF描述 |
|---|---|
| MT49H16M18CFM-xx | 288Mb SIO REDUCED LATENCY(RLDRAM II) |
| MT49H32M9C | 288Mb SIO REDUCED LATENCY(RLDRAM II) |
| MT49H32M9CFM-xx | 288Mb SIO REDUCED LATENCY(RLDRAM II) |
| MT4C1004J | 4 Meg x 1 FPM DRAM(4 M x 1快速頁面模式動態RAM) |
| MT4C4001STG-6 | standard or self refresh |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT49H16M18CBM-25 | 制造商:Micron Technology Inc 功能描述: |
| MT49H16M18CBM-25 TR | 制造商:Micron Technology Inc 功能描述:16MX18 RLDRAM PLASTIC PBF FBGA 1.8V SEPARATE I/O 8 BANKS - Tape and Reel |
| MT49H16M18CBM-33 IT | 制造商:Micron Technology Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。