- 您現在的位置：買賣IC網 > PDF目錄25633 > MR80C52EXXX-25/883 (ATMEL CORP) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44 PDF資料下載
參數資料
| 型號： | MR80C52EXXX-25/883 |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44 |
| 封裝： | LCC-44 |
| 文件頁數： | 45/46頁 |
| 文件大?。?/td> | 4720K |
| 代理商： | MR80C52EXXX-25/883 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁
98
42023G–SAM–03/2014
ATSAM4L8/L4/L2
8.11.8
Chip Erase Typical Procedure
The chip erase operation is triggered by writing a one in the CE bit in the Control Register
(CR.CE). This clears first all volatile memories in the system and second the whole flash array.
Note that the User page is not erased in this process. To ensure that the chip erase operation is
completed, check the DONE bit in the Status Register (SR.DONE). Also note that the chip erase
operation depends on clocks and power management features that can be altered by the CPU.
It is important to ensure that it is stopped. The recommended sequence is shown below:
1.
At power up, RESET_N is driven low by a debugger. The on-chip regulator holds the
system in a POR state until the input supply is above the POR threshold. The system
continues to be held in this static state until the internally regulated supplies have
reached a safe operating.
2.
PM starts, clocks are switched to the slow clock (Core Clock, System Clock, Flash
Clock, and any Bus Clocks that do not have clock gate control). Internal resets are
maintained due to the external reset.
– The debug port and access ports receives a clock and leave the reset state
3.
The debugger maintains a low level on TCK and release RESET_N.
– The SMAP asserts the core_hold_reset signal
4.
The Cortex-M4 core remains in reset state, meanwhile the rest of the system is
released.
5.
The Chip erase operation can be performed by issuing the SMAP Chip Erase com-
mand. In this case:
– volatile memories are cleared first
– followed by the clearing of the flash array
– followed by the clearing of the protected state
6.
After operation is completed, the device must be restarted by either controling
RESET_N or switching power off/on. Make sure that the TCK pin is high when releas-
ing RESET_N not to halt the core.
8.11.9
Setting the Protected State
This is done by issuing a specific flash controller command, for more information, refer to Sec-
Programming Typical Procedure” on page 97. The protected state is defined by a highly secure
Flash builtin mechanism. Note that for this programmation to propagate, it is required to reset
the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MQ83C154XXX-12/883R | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQFP44 |
| MC80C52CXXX-16P883 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MC80C32-12SBD | 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40 |
| MR83C154DCXXX-25P883 | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44 |
| MC80C52EXXX-30SHXXX:D | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MR80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MR80C86/B | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述:Microprocessor, 16 Bit, 44 Pin, Ceramic, LCC |
| MR80C86-2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MR80C86-2/883 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MR80C86-2/B | 制造商:Intersil Corporation 功能描述:MPU 80C86 16BIT CMOS 8MHZ 44PLCC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。