參數資料
型號: MPC740ARX266TX
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 266 MHz, RISC PROCESSOR, CBGA255
封裝: 21 X 21 MM, 3 MM HEIGHT, 1.27 MM PITCH, CERAMIC, BGA-255
文件頁數: 32/44頁
文件大小: 558K
代理商: MPC740ARX266TX
38
MPC750A RISC Microprocessor Hardware Specications
System Design Information
1.8.7.1 Internal Package Conduction Resistance
For the exposed-die packaging technology, shown in Table 4, the intrinsic conduction thermal resistance
paths are as follows:
The die junction-to-case (or top-of-die for exposed silicon) thermal resistance
The die junction-to-ball thermal resistance
Figure 21 depicts the primary heat transfer path for a package with an attached heat sink mounted to a
printed-circuit board.
Figure 21. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
Heat generated on the active side of the chip is conducted through the silicon, then through the heat sink
attach material (or thermal interface material), and nally to the heat sink where it is removed by forced-air
convection.
Since the silicon thermal resistance is quite small, for a rst-order analysis, the temperature drop in the
silicon may be neglected. Thus, the heat sink attach material and the heat sink conduction/convective
thermal resistances are the dominant terms.
1.8.7.2 Adhesives and Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the
thermal contact resistance. For those applications where the heat sink is attached by spring clip
mechanism, Figure 22 shows the thermal performance of three thin-sheet thermal-interface materials
(silicone, graphite/oil, oroether oil), a bare joint, and a joint with thermal grease as a function of contact
pressure. As shown, the performance of these thermal interface materials improves with increasing contact
pressure. The use of thermal grease signicantly reduces the interface thermal resistance. That is, the bare
joint results in a thermal resistance approximately 7 times greater than the thermal grease joint.
Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see
Figure 20). This spring force should not exceed 5.5 pounds of force. Therefore, the synthetic grease offers
the best thermal performance, considering the low interface pressure. Of course, the selection of any
thermal interface material depends on many factors—thermal performance requirements,
manufacturability, service temperature, dielectric properties, cost, etc.
External Resistance
Internal Resistance
(Note the internal versus external package resistance)
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MI
CO
ND
UC
TO
R,
INC
.
相關PDF資料
PDF描述
MPC7410RX450LD 32-BIT, 450 MHz, RISC PROCESSOR, CBGA360
MPC7410RX400LE 32-BIT, 400 MHz, RISC PROCESSOR, CBGA360
MPC7410RX400LD 32-BIT, 400 MHz, RISC PROCESSOR, CBGA360
MPC7410RX500LC 32-BIT, 500 MHz, RISC PROCESSOR, CBGA360
MPC7410HX450LE 32-BIT, 450 MHz, RISC PROCESSOR, CBGA360
相關代理商/技術參數
參數描述
MPC7410 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications Addendum
MPC7410_1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications
MPC7410_10 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications Addendum
MPC74-103J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Metal Plate Cement Resistors
MPC74-103K 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Metal Plate Cement Resistors