- 您現在的位置：買賣IC網 > Datasheet目錄45 > MIC2593-2BTQ TR (Micrel Inc)IC PCI HOT PLUG CTLR DUAL 48TQFP Datasheet資料下載
參數資料
| 型號： | MIC2593-2BTQ TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 4/26頁 |
| 文件大小： | 220K |
| 描述： | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| 標準包裝： | 2,000 |
| 類型： | 熱交換控制器 |
| 應用： | PCI，PCI-X |
| 內部開關： | 無 |
| 電源電壓： | 3.3V，5V，±12V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC2593-2BTQTR MIC2593-2BTQTR-ND |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
Micrel, Inc.
MIC2593
September 2008
4
M9999-092208
Pin Number
Pin Name
Pin Function
6, 31
5VINA, 5VINB
5V Supply Power and Sense Input [A/B]: Pin 6 is the (+) Kelvin-sense
connection to the supply side of the sense resistor for 5V Slot A. Pin 31 is the
(+) Kelvin sense connection to the supply side of the sense resistor for 5V Slot
B. These two pins must ultimately connect to each other within10cm of the
MIC2593. An undervoltage lockout circuit (UVLO) prevents the switches from
turning on while this input is less than its lockout threshold.
7, 30
5VSENSEA, 5VSENSEB 5V Circuit Breaker Sense Input [A/B]: The current limit thresholds are set by
connecting sense resistors between these pins and 5VIN[A/B]. When the
current limit threshold of IR = 50mV is reached, the 5VGATE[A/B] pin is
modulated to maintain a constant voltage across the sense resistor and
therefore a constant current into the load. If the 50mV threshold is exceeded for
t
FLT
(see CFILTER[A/B] pin description), the circuit breaker is tripped and the
GATE pin for the affected supplys external MOSFET is immediately pulled low.
9, 28
5VOUTA, 5VOUTB
5V Power-Good Sense Inputs: Connect to 5V[A/B] outputs. Used to monitor the
5V output voltages for Power-is-Good status.
8, 29
5VGATEA, 5VGATEB
5V Gate Drive Output [A/B]: Each pin connects to the gate of an external N-
Channel MOSFET. During power-up, the C
GATE
and the C
GS
of the MOSFETs
are charged by a 25礎 current source. This controls the value of dv/dt seen at
the source of the MOSFETs, and hence the current flowing into the load
capacitance.
During current-limit events, the voltage at the pin is adjusted to maintain constant
current through the switch for a period of t
FLT
. Whenever an overcurrent, thermal
shutdown, or input undervoltage fault condition occurs, the GATE pin for the
affected slot is immediately brought low.
During power-down, these pins are discharged by an internal current source.
12, 25
3VINA, 3VINB
3.3V Supply Power and Sense Input [A/B]: Pin 12 is the (+) Kelvin-sense
connection to the supply side of the sense resistor for 3.3V Slot A. Pin 25 is the
(+) Kelvin-sense connection to the supply side of the sense resistor for 3.3V Slot
B. These two pins must ultimately connect to each other within 10cm of the
MIC2593. An undervoltage lockout circuit (UVLO) prevents the switches from
turning on while this input is less than its lockout threshold.
13, 24
3VSENSEA, 3VSENSEB 3V Circuit Breaker Sense Input [A/B]: The current limit thresholds are set by
connecting sense resistors between these pins and 3VIN[A/B]. When the
current limit threshold of IR = 50mV is reached, the 3VGATE[A/B] pin is
modulated to maintain a constant voltage across the sense resistor and
therefore a constant current into the load. If the 50mV threshold is exceeded for
t
FLT
(see CFILTER[A/B] pin description), the circuit breaker is tripped and the
GATE pin for the affected supplys external MOSFET is immediately pulled low.
16, 21
3VOUTA, 3VOUTB
3.3V Power-Good Sense Inputs: Connect to 3.3V[A/B] outputs. Used to monitor
the 3.3V output voltages for Power-is-Good status.
14, 23
3VGATEA, 3VGATEB
3V Gate Drive Output [A/B]: Each pin connects to the gate of an external N-
channel MOSFET. During power-up, the C
GATE
and the C
GS
of the MOSFETs
are connected to a 25礎 current source. This controls the value of dv/dt seen at
the source of the MOSFETs, and hence the current flowing into the load
capacitance.
During current limit events, the voltage at this pin is adjusted to maintain
constant current through the switch for a period of t
FLT
. Whenever an
overcurrent, thermal shutdown, or input undervoltage fault condition occurs, the
GATE pin for the affected slot is immediately brought low. During power down,
these pins are discharged by an internal current source.
11, 26
VSTBYA, VSTBYB
.3V Standby Input Voltage: Required to support PCI VAUX output. Additionally,
the SMBus logic and internal registers run off of VSTBY[A/B] to ensure that the
MIC2593 is accessible during standby modes. A UVLO circuit prevents turn-on
of this supply until VSTBY[A/B] rises above its UVLO threshold. Both pins must
be connected together externally at the IC.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2594-2BM TR | IC CTRLR HOT SWAP NEG HV 8-SOIC |
| MIC2595R-2BM TR | IC CTRLR HOT SWAP NEG HV 14-SOIC |
| MIC280-7BM6 TR | IC SUPERVISOR THERMAL SOT23-6 |
| MIC2800-GFSYML TR | IC REG TRPL BUCK/LINEAR 16MLF |
| MIC281-7BM6 TR | IC SUPERVISOR THERMAL SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2593-2YTQ | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2593-2YTQ TR | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2594-1BM TR | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2594-1YM | 功能描述:熱插拔功率分布 Negative Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。