- 您現在的位置：買賣IC網 > Datasheet目錄45 > MIC2593-2BTQ TR (Micrel Inc)IC PCI HOT PLUG CTLR DUAL 48TQFP Datasheet資料下載
參數資料
| 型號： | MIC2593-2BTQ TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 11/26頁 |
| 文件大?。?/td> | 220K |
| 描述： | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| 標準包裝： | 2,000 |
| 類型： | 熱交換控制器 |
| 應用： | PCI，PCI-X |
| 內部開關： | 無 |
| 電源電壓： | 3.3V，5V，±12V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC2593-2BTQTR MIC2593-2BTQTR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
Micrel, Inc.
MIC2593
September 2008
11
M9999-092208
Functional Description
Hot Swap Insertion
When circuit boards are inserted into systems carrying
live supply voltages ( hot-plugged ), high inrush currents
often result due to the charging of bulk capacitance that
resides across the circuit boards supply pins. This
transient inrush current can cause the systems supply
voltages to temporarily go out of regulation, causing data
loss or system lock-up. In more extreme cases, the
transients occurring during a hot plug event may cause
permanent damage to connectors or on-board
components.
The MIC2593 addresses these issues by limiting the
inrush currents to the load (PCI Board), and thereby
controlling the rate at which the loads circuits turn-on. In
addition to this inrush current control, the MIC2593 offers
input and output voltage supervisory functions and current
limiting to provide robust protection for both the system
and circuit board.
System Interfaces
The MIC2593 employs two system interfaces: the
hardware Hot Plug Interface (HPI) and the System
Management Interface (SMI). The HPI includes ON[A/B],
AUXEN[A/B], as well as /FAULT[A/B]; the SMI consists of
SDA, SCL, and /INT, whose signals conform to the levels
and timing of the SMBus specification. The MIC2593 can
be operated exclusively from the SMI, or can employ the
HPl for power control while continuing to use the SMI for
access to all but the power control registers.
In addition to the basic power control features of the
MIC2593 accessible by the HPI, the SMI also gives the
host access to the following information from the part:
1. Fault conditions occurring on each supply.
2. GPI[A/B] pin status.
When using the System Management Interface for power
control, do not use the Hot Plug Interface. Conversely,
when using the Hot Plug Interface for power control, do
not execute power control commands over the System
Management Interface bus (all other register accesses via
the SMI bus remain permissible while in the HPI control
mode). When utilizing the SMI exclusively, the HPI input
pins ON[A/B] and AUXEN[A/B] should be tied to ground
as shown below in Figure 6 (Disabling HPI when SMI
control is used). This configuration safeguards the power
slots in the event that the SMBus communication link is
disconnected for any reason.
Additionally, when utilizing the HPI exclusively, the
SMBus (or SMI) will be inactive if the input pins (SDA,
SCL, A0, A1, and A2) are configured as shown in Figure 6
below (disabling SMI when HPI Control is used).
Power-On Reset and Power Cycling
The MIC2593 utilizes VSTBY[A/B] as the main supply
input source. VTSBY[A/B] is required for proper operation
of the MIC2593 SMBus interface and registers and must
be applied at all times. A Power-On Reset (POR) cycle is
initiated after VSTBY[A/B] rises above its UVLO threshold
and remains valid at that voltage for 500祍. All internal
registers are cleared after POR. If VSTBY[A/B] is
recycled, the MIC2593 enters a new power-on reset
cycle. VSTBY[A/B] must be the first supply input applied
followed by the MAIN supply inputs of 12V
IN
, 12MV
IN
,
5V
IN
, and 3V
IN
. The MAIN supply inputs may be applied in
any order. The SMBus is ready for access at the end of
the POR interval (500祍 after VSTBY[A/B] is valid). All
outputs remain off during t
POR
.
MIC2593
A2
/INT
SDA
SCL
A0
V
STBY
A1
100k
47
48
37
39
40
41
100k
Disabling SMI when
HPI Control is used
Disabling HPI when
SMI Control is used
100k
/INT
AUXENA
AUXENB
ONA
ONB
MIC2593
45
42
44
43
Figure 6. Input Pin Configuration for
Disabling HPI/SMI Control
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2594-2BM TR | IC CTRLR HOT SWAP NEG HV 8-SOIC |
| MIC2595R-2BM TR | IC CTRLR HOT SWAP NEG HV 14-SOIC |
| MIC280-7BM6 TR | IC SUPERVISOR THERMAL SOT23-6 |
| MIC2800-GFSYML TR | IC REG TRPL BUCK/LINEAR 16MLF |
| MIC281-7BM6 TR | IC SUPERVISOR THERMAL SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2593-2YTQ | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2593-2YTQ TR | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2594-1BM TR | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2594-1YM | 功能描述:熱插拔功率分布 Negative Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。