參數資料
型號： MC7457VG867NC
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 32-BIT, 867 MHz, RISC PROCESSOR, CBGA483
封裝： 29 X 29 MM, 3.22 MM HEIGHT, 1.27 MM PITCH, ROHS COMPLIANT, CERAMIC, BGA-483
文件頁數： 15/73頁
文件大小： 1715K
代理商： MC7457VG867NC
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 7
22
Freescale Semiconductor
Electrical and Thermal Characteristics
The L3_CLK timing diagram is shown in Figure 7.
Figure 7. L3_CLK_OUT Output Timing Diagram
L3 clock jitter
—
± 75
—
± 75
ps
5
Notes:
1. The maximum L3 clock frequency (and minimum L3 clock period) will be system dependent. See Section 5.2.3, “L3 Clock
AC Specifications,” for an explanation that this maximum frequency is not functionally tested at speed by Freescale. The
minimum L3 clock frequency and period are fSYSCLK and tSYSCLK, respectively.
2. The nominal duty cycle of the L3 output clocks is 50% measured at midpoint voltage.
3. Maximum possible skew between L3_CLK0 and L3_CLK1. This parameter is critical to the address and control signals which
are common to both SRAM chips in the L3.
4. Maximum possible skew between L3_CLK0 and L3_ECHO_CLK1 or between L3_CLK1 and L3_ECHO_CLK3 for PB2 or
Late Write SRAM. This parameter is critical to the read data signals because the processor uses the feedback loop to latch
data driven from the SRAM, each of which drives data based on L3_CLK0 or L3_CLK1.
5. Guaranteed by design and not tested. The input jitter on SYSCLK affects L3 output clocks and the L3 address, data, and
control signals equally and, therefore, is already comprehended in the AC timing and does not have to be considered in the
L3 timing analysis. The clock-to-clock jitter shown here is uncertainty in the internal clock period caused by supply voltage
noise or thermal effects. This is also comprehended in the AC timing specifications and need not be considered in the L3
timing analysis.
6. L3 I/O voltage mode must be configured by L3VSEL as described in Table 3, and voltage supplied at GVDD must match
mode selected as specified in Table 4. See Table 23 for revision level information and part marking.
Table 10. L3_CLK Output AC Timing Specifications (continued)
At recommended operating conditions. See Table 4.
Parameter
Symbol
Device Revision (L3 I/O Voltage) 6
Unit
Notes
Rev 1.1. (All I/O Modes)
Rev 1.2 (1.5-V I/O Mode)
Rev 1.2
(1.8-, 2.5-V I/O Modes)
Min
Typ
Max
Min
Typ
Max
L3_CLK0
VM
tL3CR
tL3CF
VM
L3_CLK1
VM
tL3_CLK
tCHCL
VM
L3_ECHO_CLK1
L3_ECHO_CLK3
VM
For PB2 or Late Write:
tL3CSKW1
tL3CSKW2
相關PDF資料
PDF描述
MC7457RX1267LC 32-BIT, 1267 MHz, RISC PROCESSOR, CBGA483
MC7457VG733NC 32-BIT, 733 MHz, RISC PROCESSOR, CBGA483
MC74ACT125DR2 ACT SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
MC74AC125DR2 AC SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
MC74ACT125DTR2 ACT SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
相關代理商/技術參數
參數描述
MC74A5-33SNTR 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
MC74A5-50T 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
MC74AC00 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:QUAD 2-INPUT NAND GATE
MC74AC00D 功能描述:邏輯門 2-6V Quad 2-Input RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel
MC74AC00DG 功能描述:邏輯門 2-6V Quad 2-Input NAND RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*