參數資料
型號: MC705JJ7CDWE
廠商: Freescale Semiconductor
文件頁數: 113/164頁
文件大?。?/td> 0K
描述: IC MCU 8BIT 224B RAM 20-SOIC
標準包裝: 38
系列: HC05
核心處理器: HC05
芯體尺寸: 8-位
速度: 2.1MHz
連通性: SIO
外圍設備: POR,溫度傳感器,WDT
輸入/輸出數: 14
程序存儲器容量: 6KB(6K x 8)
程序存儲器類型: OTP
RAM 容量: 224 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 4x12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
包裝: 管件
Operating Modes
MC68HC705JJ7 MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
52
Freescale Semiconductor
6.3.1 Stop Mode
The STOP instruction puts the MCU in a mode with the lowest power consumption and affects the MCU
as follows:
Turns off the central processor unit (CPU) clock and all internal clocks by stopping both the external
pin oscillator and the internal low-power oscillator. The selection of the oscillator by the OM1 and
OM2 bits in the ISCR is not affected. The stopped clocks turn off the COP watchdog, the core timer,
the programmable timer, the analog subsystem, and the SIOP.
Removes any pending core timer interrupts by clearing the core timer interrupt flags (CTOF and
RTIF) in the core timer status and control register (CTSCR)
Disables any further core timer interrupts by clearing the core timer interrupt enable bits (CTOFE
and RTIE) in the CTSCR
Removes any pending programmable timer interrupts by clearing the timer interrupt flags (ICF,
OCF, and TOF) in the timer status register (TSR)
Disables any further programmable timer interrupts by clearing the timer interrupt enable bits (ICIE,
OCIE, and TOIE) in the timer control register (TCR)
Enables external interrupts via the IRQ/VPP pin by setting the IRQE bit in the IRQ status and control
register (ISCR). External interrupts are also enabled via the PA0 through PA3 pins, if the port A
interrupts are enabled by the PIRQ bit in the mask option register (MOR).
Enables interrupts in general by clearing the I bit in the condition code register
The STOP instruction does not affect any other bits, registers, or I/O lines.
The following conditions bring the MCU out of stop mode:
An external interrupt signal on the IRQ/VPP pin — A high-to-low transition on the IRQ/VPP pin loads
the program counter with the contents of locations $1FFA and $1FFB.
An external interrupt signal on a port A external interrupt pin — If selected by the PIRQ bit in the
MOR, a low-to-high transition on a PA3–PA0 pin loads the program counter with the contents of
locations $1FFA and $1FFB.
External reset — A logic 0 on the RESET pin resets the MCU and loads the program counter with
the contents of locations $1FFE and $1FFF.
When the MCU exits stop mode, processing resumes after a stabilization delay of 16 or 4064 internal bus
cycles, depending on the state of the DELAY bit in the MOR.
NOTE
Execution of the STOP instruction without setting the SWAIT bit in the MOR
will cause the oscillators to stop, and, therefore, disable the COP watchdog
timer. If the COP watchdog timer is to be used, stop mode should be
changed to halt mode as described in 6.3.3 Halt Mode.
相關PDF資料
PDF描述
VI-B1H-IY-F4 CONVERTER MOD DC/DC 52V 50W
VE-B43-IX-B1 CONVERTER MOD DC/DC 24V 75W
AD724JRZ-RL IC ENCODER RGB TO NTSC 16SOIC TR
VE-B42-IX-B1 CONVERTER MOD DC/DC 15V 75W
VI-B1F-IY-F3 CONVERTER MOD DC/DC 72V 50W
相關代理商/技術參數
參數描述
MC705JJ7CDWE 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MC705JP7CPE 功能描述:8位微控制器 -MCU 8B MCU 224 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705JP7CPE 制造商:Freescale Semiconductor 功能描述:IC 8BIT MCU 68HC05 2.1MHZ DIP-28
MC705K1CP 制造商:Motorola Inc 功能描述:16 PIN DIP INTEGRATED CIRCUIT
MC705L16CFUE 功能描述:8位微控制器 -MCU 8B MCU W/ EPROM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT