參數資料
型號： MC68HC705C9AP
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP40
封裝： PLASTIC, DIP-40
文件頁數： 127/177頁
文件大小： 1941K
代理商： MC68HC705C9AP
Interrupts
Non-Maskable Software Interrupt (SWI)
MC68HC705C9A — Rev. 4.0
Advance Information
MOTOROLA
Interrupts
53
4.3 Non-Maskable Software Interrupt (SWI)
The SWI is an executable instruction and a non-maskable interrupt: It is
executed regardless of the state of the I bit in the CCR. If the I bit is zero
(interrupts enabled), SWI executes after interrupts which were pending
when the SWI was fetched, but before interrupts generated after the SWI
was fetched. The interrupt service routine address is specified by the
contents of memory locations $3FFC and $3FFD.
4.4 External Interrupt (IRQ or Port B)
If the interrupt mask bit (I bit) of the CCR is set, all maskable interrupts
(internal and external) are disabled. Clearing the I bit enables interrupts.
The interrupt request is latched immediately following the falling edge of
IRQ. It is then synchronized internally and serviced as specified by the
contents of $3FFA and $3FFB.
When any of the port B pullups are enabled, each pin becomes an
additional external interrupt source which is executed identically to the
IRQ pin. Port B interrupts follow the same edge/edge-level selection as
the IRQ pin. The branch instructions BIL and BIH also respond to the
port B interrupts in the same way as the IRQ pin. See 7.4 Port B.
Either a level-sensitive and edge-sensitive trigger or an edge-sensitive-
only trigger operation is selectable. In MC68HC05C9A mode, the
sensitivity is software controlled by the IRQ bit in the C9A option register
($3FDF). In the MC68HC05C12A mode, the sensitivity is determined by
the C12IRQ bit in the C12 mask option register ($3FF1).
NOTE:
The internal interrupt latch is cleared in the first part of the interrupt
service routine; therefore, one external interrupt pulse can be latched
and serviced as soon as the I bit is cleared.
相關PDF資料
PDF描述
MC68HC705C9AFB 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68LNC705C9ACFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
MC68HC705C9ACS 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER
MC68HC705CT4FB 8-BIT, OTPROM, 2.048 MHz, MICROCONTROLLER, PQFP44
MC68HC705CT4FN 8-BIT, OTPROM, 2.048 MHz, MICROCONTROLLER, PQCC44
相關代理商/技術參數
參數描述
MC68HC705C9AVFNE 功能描述:8位微控制器 -MCU 8B MCU 352 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC705E6CDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC705G1B 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705J1A 制造商:Freescale Semiconductor 功能描述:
MC68HC705J1ACDW 功能描述:IC MCU 4MHZ 1.2K OTP 20-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*